alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation. A guard
or other part that is damaged should be properly repaired or replaced by
an authorized service center unless otherwise indicated elsewhere in this
manual.
•
REPAIRS AND SERVICE.
Repairs, maintenance and any adjustments not
specified in this manual should be performed by Black & Decker
authorized service centers or other qualified service organizations,
always using identical replacement parts.
•
USE OF ACCESSORIES AND ATTACHMENTS.
The use of any accessory or
attachment not recommended for use with this lawnmower can increase
the risk of injury. Note: Refer to the accessory section of this manual for
further details.
ADDITIONAL WARNINGS FOR LAWNMOWERS
WARNING: Rotating blade can cause serious injury.
Release switch
lever to turn lawnmower off, wait for the blade to stop
rotating (approx. 5 seconds) and unplug the lawnmower
whenever you leave the lawnmower, before removing and
replacing the grass catcher, or unclogging or cleaning the
lawnmower housing, when making any repairs or
inspections, and when lifting, transporting or storing the
lawnmower.
•
THOROUGHLY
inspect the area where the lawnmower is to be used and
remove all stones, sticks, wires, bones, and other foreign objects that could
be thrown by the blade. Objects struck by lawnmower blade can cause
severe injury to persons.
•
NEVER
attempt to make a wheel height adjustment while the motor is
running or while the lawnmower is plugged in.
Prior to making wheel
height adjustment release switch lever to turn lawnmower off, wait for
the blade to stop rotating (approx. 5 seconds) and unplug the
lawnmower.
When making wheel height adjustments ensure all 4
wheels are moved to the same height setting and wheel nuts are
secure.
WARNING: TO AVOID THE RISK OF SERIOUS INJURY
do not operate
lawnmower unless all 4 wheels are mounted in the same
wheel height position on deck.
•
DO NOT
put hands or feet near or under rotating parts. Keep clear of the
discharge opening at all times.
•
IF LAWNMOWER
stalls, release switch lever to turn lawnmower off, wait
for the blade to stop rotating (approx. 5 seconds) and unplug the cord
before attempting to unclog the chute or remove anything from under the
deck.
•
KEEP HANDS
and feet away from cutting area.
•
USE EXTREME CAUTION
when reversing or pulling lawnmower toward you.
•
RELEASE
switch lever to turn lawnmower off and wait for the blade to stop
rotating (approx. 5 seconds) when crossing gravel drives, walks, roads
and patios.
•
AFTER STRIKING
a foreign object, release switch lever to turn lawnmower
off, wait for the blade to stop rotating (approx. 5 seconds) and unplug the
lawnmower, thoroughly inspect the lawnmower for any damage, and
repair the damage before restarting and operating the lawnmower.
•
IF THE
lawnmower should start to vibrate abnormally release switch lever
to turn lawnmower off and wait for the blade to stop rotating (approx. 5
seconds) and unplug lawnmower. Check immediately for cause. Vibration
is generally a warning of trouble.
•
MOW ACROSS
the face of slopes; never up and down. Exercise extreme
caution when changing direction on slopes. Do not mow excessively steep
slopes.
•
KEEP BLADES
sharp.
•
IF YOU
are using a grass catcher, check it frequently for wear and
deterioration. If excessively worn, replace with new bag for your safety.
•
USE IDENTICAL
replacement blades only.
Cable Strap
Handle Hex Nuts
Handle Bolts
Handle Clips
Fig. 2.
Star Washers
The following are explanations of important safety hazard
pictorials on the lawnmower.
1. User must read and understand the instruction manual.
2. To avoid the risk of serious injury do not mow up and down
slopes. Always mow across slopes.
3. To avoid the risk of injury to bystanders keep all persons
and pets at a safe distance from the lawnmower while
operating.
4. Rotating blades can cause serious injury. Keep hands and
feet clear of lawnmower deck and discharge opening at all
times, always be sure blade has stopped (wait for the blade
to stop rotating (approx. 5 seconds) after releasing switch
lever and then unplug lawnmower) before removing and
replacing grass catcher, cleaning, servicing, transporting or
lifting the lawnmower.
1
2
3
4
5
1
2
2
2
4
4
4
2
5. Objects struck by lawnmower blade can cause serious injury.
Always ensure persons and pets are clear of the discharge
from the lawnmower while operating. Always inspect
mowing area before mowing and remove objects that could
be thrown by blade. Release switch lever to turn lawnmower
off and wait for the blade to stop rotating (approx. 5
seconds) before crossing walk, roads, patios and gravel
drives.
SAVE THESE INSTRUCTIONS
UNPACKING INSTRUCTIONS
Fig. 1.
Cable Strap
Star Washer
Handle Hex Nut
Handle Bolt
Wheel Bolt
Wheel Nut
Wheel Spacer
Handle Clip
UNPACKING:
Remove lawnmower and hardware bag from the carton. See figure 1 for
hardware identification.
ASSEMBLY TOOLS REQUIRED:
2 adjustable wrenches or 3/4” and 15mm wrench for wheel bolts.
7/16” wrench for handle hex nuts. Estimated assembly time : 5 minutes
ASSEMBLY:
1. The lawnmower is shipped with all electrical connections complete.
Only wheel and handle assembly are required.
2. Attach lower handle to lawnmower deck. Spread handle legs to clear
the mounting brackets located on the lawnmower deck. Align the holes
in the lower handle legs with the bracket pins. Release the handle legs
and they will snap into place. Insert the handle clips into the grooves in
the bracket pins.
3. Assemble upper handle to lower handle. Ensure cord is on the
same side as the discharge opening. Align holes in upper and lower
handles, insert eyebolt (on cord) in handle holes. Use handle bolt
(Fig. 1) on other side. Place star washer (Fig. 1) on bolts. Place handle
nut on bolts and tighten securely. See Fig. 2.
4. Wrap the cable strap around the lower handle and the power cord.
(Fig. 2). Locate one end of the cable strap into the slot on the other end
of the cable strap and feed through forming a loop. Before tightening
the loop, align the cable strap with the hole in the lower handle. Now
you can pull the cable strap tightly around the power cord and lower
handle.
WHEEL ASSEMBLY
1. Insert an axle bolt through wheel, wheel spacer, and the hole in the
deck providing the desired cutting height. Refer to Fig. 3.
2. Place the nut on axle bolt and tighten bolt with 3/4” wrench on head
and 15mm wrench on nut.
3. Repeat for the other 3 wheels.
Important:
Be sure to mount all 4
wheels in the same wheel height position on deck and wheel nuts are
secure.
