19
20
• Reheating coffee is not recommended. Coffee is at its peak flavor immediately
after brewing.
• Small oil droplets on the surface of brewed, black coffee is due to the
extraction of oil from the coffee grounds. Oiliness may occur more frequently
if heavily roasted coffees are used. Over extraction may also cause oiliness,
indicating a need to clean your coffeemaker.
Care and Cleaning
This appliance requires little maintenance. It contains no user-serviceable parts.
Any servicing requiring disassembly other than cleaning must be performed by a
qualified appliance repair technician.
Warning: Unplug from wall outlet before cleaning.
1. Always make sure the coffeemaker is unplugged and the warming plate is
cool before attempting to clean.
2. After daily use, the removable filter basket, carafe and carafe lid should be
washed in warm, soapy water.
3. If necessary, wipe the outside of the coffeemaker with a soft, damp cloth and
wipe dry. Do not use abrasive cleansers, scouring pads or steel wool. Never
immerse the coffeemaker in water or any other liquid.
CARING FOR yOUR CARAFE
1. Do not allow all liquid to evaporate from the carafe while on the warming
plate, or heat the carafe when empty.
2. Discard the carafe if damaged in any manner.
3. Never use abrasive scouring pads or cleansers; they will scratch the glass.
4. Avoid rough handling and sharp blows.
MINERAL DEPOSITS AND CLOGGING
Mineral deposits left by hard water can clog your coffeemaker. excessive
steaming or a prolonged brewing cycle are signs that a cleaning is needed.
Cleaning is recommended every 60 brewing cycles.
1. Pour white into the carafe up to the 7-cup mark. Add cold water up to the
12-cup mark. Pour the water/vinegar mixture into the water reservoir.
2. Place a permanent filter in the removable filter basket, then close the lid.
Place the carafe on the warming plate. Press the ON/OFF button.
Note:
During cleaning, more steam will occur than during normal brewing.
3. KEEP THE COFFEEMAKER ON UNTIL HALF THE WATER HAS CYCLED
THROUGH THE COFFEEMAKER, AS CAN BE VIEWED THROUGH THE
WATER LEVEL INDICATOR. Press the ON/OFF button to turn the power off.
When liquid stops dripping from the removable filter basket into the carafe,
remove the carafe and allow the liquid to cool for 10 minutes. When cooled,
pour liquid back into the water reservoir.
4. Return carafe to the warming plate.
AUTO-ON FEATURE
To pre-set your coffeemaker to begin brewing at a later time, first follow steps
1-5 in the Brewing Instructions section. Check to make sure that the clock is
set to the correct time. If it is not, follow the above instructions to set the clock.
Press the PROGRAM Button once, the LCD Display will flash “PROGRAM”.
Press the HOUR and MIN Buttons until the desired brew time is reached. Make
sure the proper “AM/PM” appears on the left side of the LCD display. Press
the AUTO ON button. The green “AUTO” light will illuminate in the upper right
corner and the pre-set brew time will be displayed momentarily, indicating that
the coffeemaker is now waiting for the pre-set brew time to be reached before it
begins the brewing cycle.
Note:
If the AUTO ON button is pressed during the brewing process, the
brewing will stop and the unit will turn off.
To Cancel Auto On:
Press the AUTO ON button and the green light will shut off.
To re-set the Auto On time so the unit will turn on at the same pre-set time the
next day, press the AUTO ON button and the green “AUTO” light will illuminate.
Note:
The Auto On feature will turn off after completing the brewing process at
the pre-set brew time. The AUTO ON button must be pressed after each use in
order for the unit to turn on at the same pre-set time the following day.
Note:
In the event of a power outage or if the unit is unplugged, the clock will
reset to 12:00 and the Auto On feature will have to be reprogrammed.
BREW STRENGTH FEATURE
Use the Brew Strength feature when you plan on brewing only a small amount
of coffee. This feature slows down the brewing process so that the smaller
amount of coffee will have the same taste quality as when you brew an entire
carafe. The Brew Strength feature can be activated before the unit is turned ON
or during the brewing process by pressing the BREW STRENGTH button. When
this feature is activated, a coffee cup icon will be displayed in the LCD display.
Note:
To deactivate the Brew Strength feature, press the BREW STRENGTH
button again and the coffee cup icon will disappear.
AUTO SHUT-OFF FEATURE
As an added convenience, your coffeemaker has been designed with an Auto
Shut-Off feature. When the brewing cycle is complete, the coffeemaker will
automatically shut off after 2 hours.
HINTS FOR GREAT TASTING COFFEE
• A clean coffeemaker is essential for making great tasting coffee. Regular
cleaning, as specified in Care and Cleaning is highly recommended. Always
use fresh, cool water in your coffeemaker. Finer grinds, such as drip and ADC
coffee, promote fuller extraction and provide rich, full-bodied coffee. Regular
grinds will require slightly more coffee per cup to provide the strength of a
finer grind.
• Store coffee in a cool, dry place. Once coffee has been opened, keep it tightly
sealed in the refrigerator to maintain freshness. For optimum coffee, buy
whole beans and grind them just before brewing.
• Do not re-use coffee grounds since this will greatly impair coffee flavor.
