Black & Decker BDCDD12USB, Manual

Page: 7 / 84

7
ENGLISH (Original instructions)
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
u
Hold the drill firmly with two hands to control its twisting
action.
u
DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
u
Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
u
Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
u
Make sure switch turns drill on and off.
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
u
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u
Always hold the tool and screwdriver bit in a straight line
with the screw
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
charged.
Check battery pack charg-
ing requirements
Battery pack will not
charge.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
@
Warning! Before performing any maintenance on the
tool, remove the battery from the tool. Unplug the
charger before cleaning it.
Š
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Š
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
Further information is available at www.2helpU.com
Technical data
BDCDD12USB
Voltage V
DC
12
No-load speed Min -1 0 - 550 RPM
Max. torque Nm 12.5 / 26
Chuck capacity mm 1 - 10
Max Drilling capacity
Steel/wood mm 10 / 25
Weight kg 0.79 (with battery 1.04)
Battery (Not Supplied) BDCB12
Voltage Vdc 12
Capacity Ah 1.5
Type Lithium-Ion
Charger
Input voltage V
AC
100-240V
Output voltage V
DC
5V
Output current A 1
Approx. charge time Hours 1.5
Level of sound pressure according to EN 62841:
Sound pressure (L
pA
) 62.8 dB(A), uncertainty (K) 5 dB(A)
Sound power (L
WA
) 73.8 dB(A), uncertainty (K) 5 dB(A)
Vibration total values (triax vector sum) according to EN 62841:
Drilling into metal (a
h, D
) <2.5 m/s
2
, uncertainty (K) 1.5 m/s
2