Black & Decker BCD7122, Original Instructions Manual

Page: 7 / 40

7
ENGLISH (Original instructions)
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
Electrical safety
This charger is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
‹
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. Battery
6. Battery release button
7. Charger
8 LED
9 Dual speed range
Assembly
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use and whenever
it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging temp-
erature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
‹
Plug the charger (7) into any standard 230 Volts 50 Hz
electrical outlet.
‹
Slide the battery into the charger as show in figure
A.
‹
The green LED (8) will flash indicating that the battery is
being charged
‹
The completion of charge is indicated by the green LED
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
Warning! Do not use tool while it is connected to the charger.
Warning! fire Hazard. When disconnecting the charger from
the tool, be sure to unplug the charger from the outlet first,
then disconnect the charger cord from the tool.
Installing and removing the battery pack from the
tool (fig. B)
Warning! Make certain the lock-off button is engaged to
prevent switch actuation before removing or installing battery.
To install battery pack:
‹
Insert battery pack into tool, until an audible click is heard
(fig. B)
Removing the battery pack from the tool (fig. C)
‹
Depress the battery release button as show in (fig. C)
and pull battery pack out of tool.
Operating Instructions
Trigger switch & reversing button (fig. D)
‹
The drill is turned ON and OFF by pulling and releasing
the trigger switch (1). The farther the trigger is depressed,
the higher the speed of the drill operates at
‹
A forward/reverse control button (2) determines the direc-
tion of the tool and also serves as a lock off button.
‹
To select forward rotation, release the trigger switch and
depress the forward/reverse control button to the left.
‹
To select reverse, depress the forward/ reverse control
button the opposite direction.
‹
To lock the tool, set the forward/reverse slider into the
centre position.
Note! The center position of the control button locks the tool
in the off position. When changing the position of the control
button, be sure the trigger is released.
Torque control (fig. E)
This tool is fitted with a torque adjustment collar (3) to select
the operating mode and to set the torque for tightening
screws.
Large screws and hard workpiece materials require a higher
torque setting than small screws and soft workpiece materials.
‹
For drilling, set the collar to the drilling position symbol
‹
For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriate setting, proceed as
follows:
‹
Set the collar to the lowest torque setting.
‹
Tighten the first screw.
‹
If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.