6
ENGLISH
(Original instructions)
Fitting and removing a drill bit or screwdriver bit
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits.
u
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u
Open the ssingle sleeve chuck (6) by turning it.
u
Insert the bit shaft into the chuck and firmly tighten the
single sleeve chuck.
This tool is supplied with a screwdriver bit in the bit holder (7).
u
To remove the screwdriver bit from the bit holder, lift the bit
from the recess.
u
To store the screwdriver bit, firmly push it into the holder.
Warning!
Do not attempt to tighten drill bits (or any other
accessory) by gripping the single sleeve chuck and turning
the tool on. Damage to the single sleeve chuck and personal
injury may occur when changing accessories.
Use
Warning!
Let the tool work at its own pace. Do not overload.
Warning!
Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Charging the battery (fig. A)
The battery needs to be charged before first use and whenev
-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning!
Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u
To charge the battery (8), insert it into the charger (9).
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
u
Plug in the charger and switch on at the mains.
The charging indicator (10) will blink.
The charge is complete when the charging indicator (10)
switches to continuously on. The charger and the battery can
be left connected indefinitely. The LED will switch on as the
charger occasionally tops up the battery charge.
u
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator (10) will flash red at a fast rate. Proceed as
follows:
u
Re-insert the battery (8).
u
If the charging indicators continues flashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
u
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u
If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
u
To select forward rotation, push the forward/reverse slider
(2) to the left.
u
To select reverse rotation, push the forward/reverse slider
to the right.
u
To lock the tool, set the forward/reverse slider into the
centre position.
Switching on and off
u
Select forward or reverse rotation using the forward/re-
verse slider (2).
u
To switch the tool on, press the switch (1). The tool speed
depends on how far you press the trigger switch.
u
To switch the tool off, release the trigger switch.
Autoselect
TM
technology (fig. D)
u
For drilling in wood, metal and plastics, press the drill
mode selector button (3).
u
For screwdriving, press the screwdriver mode selector
button (4).
