9
ENGLISH
Chain tension adjustment (
fi
g. C)
Warning!
Before adjusting the chain tension or any other
adjustments, make sure that the tool is switched off and the
battery removed.
Warning!
The chain guide bar and the saw chain may be hot
after use. Allow to cool before adjustment.
The product comes ready assembled. However we
recommend that you check the tension of the saw chain (14),
and chain access cover retention bolts before use and adjust
if required.
Checking and adjusting the saw chain tension
(
fi
g. C)
To tension the saw chain (14) slacken the two chain cover
retention bolts (12) with the spanner (13) and the chain
tensioning device will push the chain guide bar (3) out, setting
the correct tension. Retighten the two retention bolts (12)
securely.
Check the correct tension has been set by lightly pulling on
the saw chain (14). The tension is correct when the saw chain
snaps back after being pulled 3 mm away from the guide bar.
There should be no "sag" between the chain guide bar (3) and
the saw chain (14) on the underside.
Note:
Do not over tension the saw chain as this will lead to
excessive wear and reduce the life of the bar and saw chain. It
will also lead to reduced product performance.
Note:
With
fi
rst use and when the saw chain is new, check
tension frequently as a new saw chain stretches slightly.
Replacing the saw chain and chain guide bar
After prolonged use the saw chain (14) and /or chain guide
bar (3) may need replacing. Ensure only Black & Decker
recommended replacements are used.
Removing the saw chain and chain guide bar
(
fi
g. C & D)
Always wear protective gloves when installing
or removing the saw chain (8). The saw chain is
sharp and can cut you when it is not running.
Warning!
The chain guide bar and the saw chain may be hot
after use. Allow to cool before replacing.
Place the tool on a
fi
rm surface.
Rotate the two retention bolts (12) counter clockwise with
the spanner (13) provided and remove completely.
Remove the chain access cover (11).
Slide the latch (5) to the unlock position, open the handles
and pull back the top jaw (1).
Pull back chain guide bar (3) and then lift the saw chain
(14) out of the groove in the guide bar. The saw chain can
then be removed from the unit.
The chain guide bar (3) can then be angled up and removed.
Assembling the chain guide bar and saw chain
(
fi
g. E & F)
Warning!
Always wear protective gloves when installing or
removing the saw chain. The saw chain is sharp and can cut
you when it is not running.
Ensure the operation is carried out on a
fi
rm surface.
Slide the latch (5) to the unlock position, open the handles
and pull back the top jaw (1).
Insert the chain guide bar (3) into the space between the
chain tensioner and align with the chain guide bar locator,
angle the chain guide bar (3) down ensuring it is correctly
located.
Place the saw chain (14) around the front of the chain
guide bar (3).
Pull the chain guide bar (3) and the saw chain (14) back,
engaging it in the groove in the chain guide bar (3) and
then over the sprocket (16) positioning teeth in the correct
position on the sprocket.
Replace the chain access cover (11) and the two retention
bolts (12) tightening securely.
Ensure the saw chain (14) is
fi
tted correctly with reference
to the markings on the tool.
Oiling (
fi
g. G)
Before
fi
rst use and every ten minutes of use you must
oil the product with the correct chain oil. (Cat No A6027)
Open the oiling cover (4) and insert the bottle into the
oil
fi
lling hole (15), apply pressure to the bottle once to
dispense oil.
This should be adequate for about 10 minutes of cutting
depending upon cutting speed and type of wood.
The hole feeds the oil through to the saw chain on to the
chain guide bar (3) and an excessive amount of oil applied to
the unit could mean the oil drips from the unit around the jaw
area. This is normal and is nothing to be concerned about.
Use
Charging the battery (
fi
g. H) (not included with
GKC1000LB)
Warning!
Do not charge the battery at ambient temperatures
below 10°C or above 40°C. Recommended charging
temperature is approximately 24°C.
Note: The charger will not charge a battery pack if the cell
temperature is below approximately 0°C or above
40°C.The battery should be left in the charger and the
charger will begin to charge automatically when the cell
temperature warms up or cools down.
To charge the battery (6), insert it into the charger (9). The
battery will only
fi
t into the charger one way. Do not force.
Make sure that the battery pack is fully seated in the
charger (9).
