GENERAL SAFETY RULES
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
•
Keep your work area clean and well lit.
Cluttered benches and dark areas invite accidents.
•
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,
gases, or dust.
Power tools create sparks which may ignite the dust or fumes.
•
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to
lose control.
ELECTRICAL SAFETY
•
Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any
way
. Double insulation
eliminates the need for the three wire grounded power cord and grounded
power supply system.
•
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators.
There is
an increased risk of electric shock if your body is grounded.
•
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
•
Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately.
Damaged
cords increase the risk of electric shock.
•
When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W".
These
cords are rated for outdoor use and reduce the risk of electric shock.
PERSONAL SAFETY
•
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use
tool while tired or under the influence of drugs, alcohol, or medication.
A moment of inattention while
operating power tools may result in serious personal injury.
•
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts.
Loose clothing, jewelry, or long hair can be caught in moving parts.
•
Avoid accidental starting. Be sure switch is off before plugging in.
Carrying tools with your finger on the
switch or plugging in tools that have the switch on invites accidents.
•
Remove adjusting keys or wrenches before turning the tool on.
A wrench or key that is left attached to a
rotating part of the tool may result in personal injury.
•
Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enables better
control of the tool in unexpected situations.
•
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
TOOL USE AND CARE
•
Use clamps or other practical way to secure and support the workpiece to a stable platform.
Holding the
work by hand or against your body is unstable and may lead to loss of control.
•
Do not force tool. Use the correct tool for your application.
The correct tool will do the job better and safer
at the rate for which it is designed.
•
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
•
Disconnect the plug from the power source before making any adjustments, changing accessories, or
storing the tool.
Such preventative safety measures reduce the risk of starting the tool accidentally.
•
Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of
untrained users.
•
Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools, with sharp cutting
edges are less likely to bind and are easier to control.
•
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that
may affect the tools operation. If damaged, have the tool serviced before using.
Many accidents are
caused by poorly maintained tools.
•
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may
be suitable for one tool, may become hazardous when used on another tool.
SERVICE
•
Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by
unqualified personnel could result in a risk of injury.
•
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual.
Use of unauthorized parts or failure to follow Maintenance Instructions may create
a risk of electric shock or injury.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activ-
ities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your expo-
sure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic particles.
The label on your tool may include the following symbols.
V ..........................volts
A ........................amperes
Hz ........................hertz
W ......................watts
min ......................minutes
......................alternating current
....................direct current
no ......................no load speed
........................Class II Construction
........................earthing terminal
........................safety alert symbol
.../min ................revolutions or
reciprocations
per minute
CAT. NO. FS500,FS550,FS600,FS1000 FORM NO. 387118 PRINTED IN U.S.A. (JUN 00 CD -2)
KEY INFORMATION YOU SHOULD KNOW:
•Never operate the sander without recommended sandpaper properly installed on the
Velcro™ base. (Models FS550, FS1000)
•Do not push down—let the sander do the work.
•Extended drywall sanding is not recommended for this product.
1-800-54-HOW-TO
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PURCHASE,
CALL 1-800-54-HOW-TO (1-800-544-6986).
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE
CAN RESOLVE YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT,
GIVE US A CALL. YOUR FEEDBACK IS VITAL
TO THE SUCCESS OF BLACK & DECKER'S QUALITY
IMPROVEMENT PROGRAM.
(544-6986)
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA.
ADVERTENCIA:
LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
INSTRUCTION MANUAL
FS500, FS550, FS600, FS1000
P
P
P
P
a
a
a
a
ll
ll
m
m
m
m
G
G
G
G
rr
rr
ii
ii
p
p
p
p
SS
SS
a
a
a
a
n
n
n
n
d
d
d
d
e
e
e
e
rr
rr
ss
ss
SAFETY WARNINGS AND INSTRUCTIONS: DOUBLE INSULATION
Double insulated tools are constructed throughout with two separate layers of electrical insulation or a double
thickness of insulation between you and the tool’s electrical system. Tools built with double insulation are not
intended to be grounded. As a result, your tool is equipped with a two prong plug which permits you to use
extension cords without concern for maintaining a ground connection.
Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
REPLACEMENT PARTS:
When servicing use only identical replacement parts. Repair or replace damaged
cords.
SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk of electric shock.
When provided, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not
change the plug in any way.
SAFETY WARNINGS AND INSTRUCTIONS: SANDERS
•
ALWAYS WEAR EYE PROTECTION.
• Clean your tool out periodically.
OTHER IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS
EXTENSION CORDS
When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following
table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the gage number, the heavier the cord.
SANDING LEAD BASED PAINT
Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the contaminated
dust. The greatest danger of lead poisoning is to children and pregnant women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we recommend
the following precautions when sanding any paint:
PERSONAL SAFETY
• No children or pregnant women should enter the work area where the paint sanding is being done until all
clean up is completed.
• A dust mask or respirator should be worn by all persons entering the work area. The filter should be
replaced daily or whenever the wearer has difficulty breathing.
Minimum Gage for Cord Sets
Volts
Total Length of Cord in Feet
120V
0-25
26-50
51-100
101-150
240V
0-50
51-100
101-200
201-300
Ampere Rating
More
Not more
American Wire Gage
Than
Than
0
-
6
18
16
16
14
6
-
10
18
16
14
12
10 -
12
16
16
14
12
12 -
16
14
12
Not Recommended
FRONT
®
;;;;;;;
;;;;;;;
;;;;;;;
;;;;;;;
®
1
2
®
OFF
ON
ON OFF SWITCH (FS500, FS550, FS600, FS1000)
INTERRUPTEUR
INTERRUPTOR DE ENCENDIDO Y APAGADO
TWO SPEED ON OFF SWITCH
INTERRUPTEUR À DEUX VITESSES
INTERRUPTOR DE ENCENDIDO Y APAGADO DE DOS VELOCIDADES
OFF
ON
EXTRA TIPS
CONSEILS SUPPLÉMENTAIRES
PUNTAS ADICIONALES
3
4
5
