BKI BLF-F Installation & Operation Manual Download Page 37 | Manualshive

Page: 37 / 42

background image

Electric Autolift Fryer

Maintenance

34

13.

Add approximately 4 to 6 ounces of distilled (white) vinegar to develop a neutralizing solution. Stir
the solution briefly. Leave in the pot for three to five minutes and discard.

NOTE: Foaming of

shortening after boil-outs is caused by failure to follow proper neutralizing procedures.

14. Repeat steps 12 through 14 as needed to remove all traces of cleaning solution.

15.

Rinse the pot again with Cool water, drain and discard.

Damage to the fryer could result if the fryer pot is not completely dry before filling
with shortening. Refill the fryer pot with shortening ONLY when it is completely dry.

16. Dry the fryer pot and filter vat

COMPLETELY.

17. Close the main drain and fill with new shortening to the proper level.

«
...
35
36
37
38
39
...
»

Summary of Contents for BLF-F











































Reviews:

No comments

Related manuals for BLF-F

Brand: Garland Pages: 12

Brand: Garland Pages: 20

Brand: Gardner Denver Pages: 70

Silverlink 600 DF7

Brand: Lincat Pages: 17

Brand: Masterbuilt Pages: 48

Brand: Campomatic Pages: 30

Brand: Kalorik Pages: 40

BabyMedi CTMEHZ-I

Brand: Mediclinics Pages: 9

Brand: Mediclinics Pages: 21

Sure-Crisp 31436

Brand: Hamilton Beach Pages: 5

Brand: Bosch Pages: 36

Brand: Bosch Pages: 10

Brand: Bosch Pages: 56

Brand: Bosch Pages: 68

Brand: Bosch Pages: 68

Brand: Bosch Pages: 40

Brand: Bosch Pages: 52

Brand: Bosch Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands