BK Precision 9130 Instruction Manual Download Page 36

Page: 36 / 51

Example: SYST:RWL

SYSTem:ADDRess

This command reads the communication address of the power supply.

Command syntax: SYSTem:ADDRess?

Example: SYST:ADDR?

STATus:QUEStionable:ENABle

This command sets the parameter of the quest event enable register. This parameter determines which bit of

the quest event register is set to 1. If a QUES condition changes, the QUES bit of status byte register will

be set to 1.

Command syntax: STATus:QUEStionable:ENABle <parameter>

Parameter: 0~255

Reset value: Consult PSC command

Example: STAT:QUES:ENAB 110

STATus:QUEStionable:ENABle?

This query returns a value which corresponds to the binary weighted sum of all bits enabled by

STAT:QUIES:ENAB command. After this command executed, quest event enable register is reset.

Command syntax: STATus:QUEStionable:ENABle

？

Return parameter: <NR1>

Example : STAT:QUES:ENAB?

STATus:QUEStionable?

This command reads parameters from the quest event register. After this command executed, quest event

Command syntax: STATus:QUEStionable[:EVENt]?

Return parameter: <NR1>

Example: STAT:QUES?

STATus:QUEStionable:CONDition?

This command queries the parameter of the quest condition register. When a bit value of the quest condition

parameter changes, the corresponding bit value in the quest event register will be set to 1.

Command syntax:: STATus:QUEStionable:CONDition?

Return parameter: <NR1>

Example: STAT:QUES:COND?

STATus:OPERation ENABle

This command sets the parameter of the operation event enable register. The parameter determines which bit

value of quest event register is set to 1. If a OPER condition changes, the OPER bit of the status byte

Command syntax: STATus: OPERation:ENABle

Summary of Contents for 9130




















































Search results

Summary of Contents for 9130

Reviews:

Related manuals for 9130

Brands by name

Popular brands

BK Precision 9130, Instruction Manual

Search results

Summary of Contents for 9130

Reviews:

Related manuals for 9130

Brands by name

Popular brands