manualshive.com logo in svg

BIXOLON SRP-Q300, Connection Manual

Share
Download
BIXOLON SRP-Q300 Connection Manual Download Page 14

 

Rev. 1.01 

- 14 - 

SRP-Q300/302 

 

6. How to Connect (B-gate only) 

 

Both Ethernet and WLAN can be configured through the printer’s Ethernet interface. 

Likewise, both Ethernet and WLAN can also be configured though the printer’s WLAN 

interface. When you want to change the Ethernet or WLAN of the printer, the network 

settings of the host (PC, PDA, etc) and Ethernet or WLAN of the printer must configured 

properly configured so that communication can be established. 

 

(1) Connecting B-gate 

 

1) Ethernet(LAN) 

Connect the LAN cable to the B-gate. 

A direct cable or cross cable can be connected to the Hub or Host for use. 

 

2) WLAN 

Connect to the AP (Access Point) configured in Infrastructure mode in order to connect   

to the LAN/wireless network.   

 

 

 

 

 

 

   

Infrastructure mode 

 

In order to configure the network between HOST to B-gate, connect to the terminal in 

Ad-hoc Mode. 

 

   

   

   

 

 

Ad-hoc mode 

A P 

 

Summary of Contents for SRP-Q300

































Reviews:

No comments

Brands by name

Popular brands

Load more brands