Bivocom TG451-LF User Manual Download

Page: 11 / 49

Add: Unit 704, No. A3 Buidling, Tel.: +86-592

‐

6211713

Software Park, Xiamen, China 361000 Fax: +86-592

‐

6211727

www.bivocom.com

[email protected]

2.3 LED Indicators

TG451 Series Gateway provides LED indicators, as following.

Indicator

Status

Content

Power

Powered On

Off

Powered Off

Signal Strength

1 Lights

Signal weak

2 Lights

Signal Middium

3 Lights

Signal Strong

System

Blink

System works

Off

System doesn’t work

Online

Gateway accesses to Internet

Off

Gateway

doesn’t access to Internet

Alarm



SIM/UIM Card is not insert corectly or broken



Antenna signal is too weak

1 Blink Per

Second

Cellular module was not registered to Gateway

2 Blinks Per

Second

Gateway

can’t access to Internet

Off

Gateway

doesn’t have any alarm

WIFI

WIFI Enabled

Off

WIFI Disabled

WAN

WAN is connected

Off

WAN is not connected

LAN

LAN1 Blink

LAN1 works

LAN2 Blink

LAN2 works

LAN3 Blink

LAN3 works

LAN4 Blink

LAN4 works

Summary of Contents for TG451-LF


















































Search results

Summary of Contents for TG451-LF

Reviews:

Related manuals for TG451-LF

Brands by name

Popular brands

Bivocom TG451-LF, User Manual

Search results

Summary of Contents for TG451-LF

Reviews:

Related manuals for TG451-LF

Brands by name

Popular brands