40
KT-200-2
y
Disconnect the cable connection
between FI and compressor:
Remove the screened FI cable from
the motor pins U/V/W in the terminal
box of the compressor. Insulate the
cable ends.
y
Change the compressor motor to
star wiring:
- Remove the jumper between the
motor pins (delta wiring):
- Bridge the motor pins Z/X/Y (star
wiring, fig. 14).
y
FI
とコンプレッサー間のケーブルの
接続を外します。コンプレッサーの
端子ボックスのモーターピン
U/V/W
か ら
FI
シ ー ル ド ケ ー ブ ル を 外 し
ます。ケーブル端部を絶縁します。
y
コンプレッサーモーターをスター配
線に変更します。
-
モーターピン間のジャンパーを外し
ます(デルタ配線):
-
モ ー タ ー ピ ン
Z/X/Y
を ブ リ ッ ジ し
ます(スター配線、図
14
)。
!
!
Attention!
Danger of motor damage!
It is absolutely necessary to
change the compressor motor
from delta to star wiring!
!
!
注意!
モーターが損傷するおそれがあります!
必ずコンプレッサーモーターをデルタ配
線からスター配線に変更してください。
y
Connect a new cable between
contactor K1 and motor pins of the
compressor (see fig. 14):
- Use a new cable that has an eye
on compressor side.
- Phase L1:
Connect terminal 2 (K1) to motor
pin U.
- Phase L2:
Connect terminal 4 (K1) to motor
pin V.
- Phase L3:
Connect terminal 6 (K1) to motor
pin W.
y
Close the cover of the terminal
boxes of compressor and
condensing unit.
y
Mount the front grating of the
weather protective housing.
y
Mount main fuse and switch on main
switch.
y
コンプレッサーのコンタクター
K1
と
モーターピン間に新しいケーブルを
接続します(図
14
を参照):
-
コ ン プ レ ッ サ ー 側 に リ ン グ ア イ の
付いている新しいケーブルを使用し
てください。
-
位相
L1
:
端子
2
(
K1
)をモーターピン
U
に接続
します。
-
位相
L2
:
端子
4
(
K1
)をモーターピン
V
に接続
します。
-
位相
L3
:
端子
6
(
K1
)をモーターピン
W
に接続
します。
y
コンプレッサーとコンデンシングユ
ニットの端子ボックスのカバーを閉
じます。
y
耐候性ハウジングのフロントグリル
を取り付けます。
y
メ イ ン ヒ ュ ー ズ を 取 り 付 け て 、 メ
インスイッチをオンにします。
Fig. 13 View into the terminal box of the
condensing unit
図
13
コンデンシングユニットの端子ボックス
Summary of Contents for ECOSTAR LHV6/2DC-3.F1
