HXO-501-1 AUS
7
"Y"
"Y"
"X"
"X"
5000
1600
SCALE
PART No.
COPYRIGHT DRAWING: The information contained herein is the prop
erty of BITZER Australia. & shall not be copied, reproduced,
used for manufacture or for any other purpose without the prior
written permission of BITZER Australia.
DATE
DRAWN BY
BDC 5F-6R-H MAIN ASSY
1:50
A3
SHT.4 of 4
BITZER
AUSTRALIA
Pty Ltd
A.B.N. 70 057 670 023
3rd ANGLE
PROJECTION
DATE
APPROVED BY
INSPECTION DIMENSIONS
XXXXX
DECIMAL : ± 1.0mm
ONE DECIMAL : ± 0.5mm
TWO DECIMAL : ± 0.2mm
ANGLE : ± 0.5°
U.N.O TOLERANCES
MASS (kg)
MATERIAL & FINISH
NAME
DO NOT SCALE
ALL DIMENSIONS ARE IN mm
UNLESS OTHERWISE SPECIFIED.
DRAWING STANDARD AS1100
971.93
BDC 5F-6R-H MAIN ASSY (INSTALLATION)
T.CAVANAGH
-
01/08/17
-
REFER BOM / -
"Y"
"Y"
"X"
"X"
5000
1600
SCALE
PART No.
COPYRIGHT DRAWING: The information contained herein is the prop
erty of BITZER Australia. & shall not be copied, reproduced,
used for manufacture or for any other purpose without the prior
written permission of BITZER Australia.
DATE
DRAWN BY
BDC 5F-6R-H MAIN ASSY
1:50
A3
SHT.4 of 4
BITZER
AUSTRALIA
Pty Ltd
A.B.N. 70 057 670 023
3rd ANGLE
PROJECTION
DATE
APPROVED BY
INSPECTION DIMENSIONS
XXXXX
DECIMAL : ± 1.0mm
ONE DECIMAL : ± 0.5mm
TWO DECIMAL : ± 0.2mm
ANGLE : ± 0.5°
U.N.O TOLERANCES
MASS (kg)
MATERIAL & FINISH
NAME
DO NOT SCALE
ALL DIMENSIONS ARE IN mm
UNLESS OTHERWISE SPECIFIED.
DRAWING STANDARD AS1100
971.93
BDC 5F-6R-H MAIN ASSY (INSTALLATION)
T.CAVANAGH
-
01/08/17
-
REFER BOM / -
"Y"
"Y"
"X"
"X"
5000
1600
SCALE
PART No.
COPYRIGHT DRAWING: The information contained herein is the prop
erty of BITZER Australia. & shall not be copied, reproduced,
used for manufacture or for any other purpose without the prior
written permission of BITZER Australia.
DATE
DRAWN BY
BDC 5F-6R-H MAIN ASSY
1:50
A3
SHT.4 of 4
BITZER
AUSTRALIA
Pty Ltd
A.B.N. 70 057 670 023
3rd ANGLE
PROJECTION
DATE
APPROVED BY
INSPECTION DIMENSIONS
XXXXX
DECIMAL : ± 1.0mm
ONE DECIMAL : ± 0.5mm
TWO DECIMAL : ± 0.2mm
ANGLE : ± 0.5°
U.N.O TOLERANCES
MASS (kg)
MATERIAL & FINISH
NAME
DO NOT SCALE
ALL DIMENSIONS ARE IN mm
UNLESS OTHERWISE SPECIFIED.
DRAWING STANDARD AS1100
971.93
BDC 5F-6R-H MAIN ASSY (INSTALLATION)
T.CAVANAGH
-
01/08/17
-
REFER BOM / -
Figure 2.1 - Part 2/2
* Maximum height of solid air restriction from condenser platform is 2.8m.
**Avoid obstructions within 2 x Diameter of fan above condenser
For alternative condenser deck arrangements, please contact BITZER Australia.
Model/s
(Dimensions in mm)
BDC 152
H (2F)
BDC 228 H
(3F)
BDC 304
H (4F)
BDC 380
H (5F)
X
1050
1575
2100
2625
Y
1500
2250
3000
3750
* Avoid horizontal air discharge installation where prevailing wind
would create additional static load on fans, especially at low fan
speeds (< 680 RPM)
5.
Electrical Connections
•
EC Fan motors are suitable for 400 Volt ±10%, 50 Hz operation.
•
All three phase motors are pre-wired to an independent isolation switch within an IP56 rated electrical
junction box mounted on the condenser.
•
These motors are to be wired in accordance with Fig. 3 (wiring diagram R55000117 shown over the page).
