background image

www.BISSELL.com.au

11

Cleaning Sealed Hard Floors

When fully charged, press the ON/OFF 

Button and the three LED lights will 

illuminate.

Recline the body of the unit backward 

to start the rotating mop pads.

1

TIP 3: 

For optimum cleaning, perform overlapping cleaning strokes while dispensing 

cleaning formula. Care should be taken to not overwet the floor surface, especially 

when cleaning wood and other delicate floor surfaces.

ATTENTION: 

This machine is designed to be used only on sealed hard floors and 

should not be used on carpet or rugs. For best cleaning results, sweep or vacuum the 

floor surface prior to using to avoid scratching or damaging floors from sharp debris.

TIP 1: 

You may feel a slight vibration when turning ON the machine if the mop pads 

are not aligned correctly. Wait a few seconds for the pads to adjust themselves. If this 

doesn’t occur, turn the machine OFF and replace mop pads following the instructions 

in ‘Attaching Mop Pads’ sections.

TIP 4: 

When cleaning near baseboards, edges or furniture you may feel a slight pull 

from the unit due to bouncing off the surface. 

TIP 2: 

When you press the ON/OFF Button to start the unit the LED lights will 

illuminate, but the mop pads will not start rotating until the unit is reclined. 

2

Summary of Contents for SPINWAVE 2240F

















Reviews: