Bissell PowerWash Deluxe, Manual

Page: 8 / 11

C6 – Ready Tools™
Your deep cleaner comes equipped with
a hose and at least one cleaning tool for
cleaning stairs, upholstery, and more.
Important! If using to clean upholstery,
check upholstery tags.
1.
Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can use
your deep cleaner. If tag is coded with “X” or
“S” (with a diagonal strike through), or says
“Dry Clean Only,” do not proceed with any
deep cleaning machine. Do not use on velvet
or silk. If manufacturer’s tag is missing or not
coded, check with your furniture dealer.
2. To begin cleaning with attachments,
follow instructions on page 7 for filling 2-in-1
water tank.
3.
Set ReadyTools dial to TOOLS setting.
This will allow spray and suction from hose.
4. Attach cleaning tool of your choice to end
of hose.
5. Hold tool approximately 2.5 cm above
soiled surface. Press spray trigger to apply
cleaning solution to soiled area. Using brush
on tool, gently scrub area to be cleaned.
Release spray trigger, apply downward
pressure on tool and pull it toward you
to suction up dirt and cleaning solution.
Continue until no more dirt can be removed.
Caution: Do Not Overwet.
6.
When finished cleaning, remove and rinse
tool(s) in clean, running water.
7. It is recommended that you suction clean
water from the tap to rinse out the hose. Be
careful not to over-fill your tank.
8. Before wrapping hose onto rack, lift end
of hose and stretch out to ensure all water
is cleared from hose.
9.
Wrap hose around rack.
10. Empty 2-in-1 water tank and rinse out,
following instructions on the previous page.
11. If ReadyTools dial becomes difficult to turn,
the diverter assembly that holds dial may need
to be cleaned. To clean, first remove nozzle and
locate screw that holds diverter assembly in
place. With a Phillips screwdriver, remove the
screw and set aside.
12.
Remove diverter assembly; hold under
running water making sure water flows
through and around dial. Turn dial about 10
times clockwise and 10 more times counter
clockwise. This should free up any debris.
13. Wipe diverter assembly with a soft
cloth and replace back on machine.
Replace nozzle.
14. Return ReadyTools dial to FLOOR
CLEANING setting.
C7 – Hard Floor Cleaning
Your deep cleaner may have included a
hard floor tool and 2X Hard Floor Solutions
Formula. If not, these products are available
for purchase by contacting the BISSELL
Consumer Care department by phone or
at the website. The hard floor tool provides
effective cleaning for linoleum, vinyl, and tile
floors.
Caution: Do not use on unsealed hardwood
floors.
1. Thoroughly vacuum or sweep floor to pick
up any debris.
NOTE: Prior to filling with formula and
water be sure all carpet cleaning formula is
thoroughly rinsed from tank.
2. Fill the bladder with clean hot tap water
and set aside.
3. Fill BISSELL 2X Hard Floor Solutions
Formula to the indicated fill line in the pro-
vided measuring cup and pour into mouth of
bladder. Set tank aside until after hard floor
tool is installed.
4. Fully detent handle and let it rest on the
floor. Lift machine base so that underside
is easily accessible, then attach the hard
floor tool to the bottom of the machine by
hooking it into the nozzle and swinging it
down until it clicks into place.
5.
Place tank in to machine base, seating
firmly in base. Be sure the ReadyTools dial
is set to FLOOR CLEANING.
6. Plug into an outlet and turn the power on.
7. Plan your cleaning route to leave an exit
path. Be sure to allow adequate time for
floors to dry.
8.
While pressing the spray trigger, make one
slow forward wet pass and another back.
Caution: Do Not Overwet.
9. Repeat the motion without pressing the
trigger using the hard floor tool to squeegee
and suction up the dirty water.
10. When finished, remove hard floor tool,
rinse and let dry before storing. Refer to the
Care & Storage section on the next page for
machine clean up and storage instructions.
www.BISSELL.com
8