background image

Vacuum cleaner won’t run

Possible Causes

 

Remedies

 

Power cord not plugged in 

 

Check electrical plug

 

Thermal protector activated 

 

Allow cleaner to cool for 30 minutes,

  

 

 

see pg. 13

No Power at Rotating Floor Brush

Possible Causes

 

Remedies

 

Cylinder is not securely seated 

 

Remove Cylinder and replace, making

 

 

 

sure that it “clicks” into place

 

Brush Switch turned to “Off” 

 

Make sure Brush Switch is in “On” position

 

Vacuum is in Upright Position 

 

Recline vacuum to operate brush 

Vacuum cleaner won’t pick up dirt

Possible Causes

 

Remedies

 

Incorrect Height Adjustment 

 

Adjust Powerfoot to correct height setting

 

Hose not attached to suction opening 

 

Grasp Hose Grip and firmly push onto 

  

 the 

base

 

Crack or hole in Hose 

 

Check Hose and replace if needed

 

Drive Belt broken, worn or off motor pulley 

 

Reposition or replace Drive Belt, see 

  

 pg. 

11-12

 

Rotating Floor Brush bristles worn 

 

Replace Brush

 

Rotating Floor Brush jammed 

 

Remove Brush and clean debris from 

  

 Brush 

Ends

 

Clog in vacuum 

 

Follow instructions on pg. 13 for 

  

 clearing 

clogs

 

Dirt Container full 

 

Empty Dirt Container

 

Dirt Container or Upper Tank  

 

Position correctly and lock in place

 

not installed properly

 

Filters are dirty 

 

Check and clean or replace Upper Tank, 

 

 

 

Pre-Motor and Post-Motor Filters

Vacuum cleaner is difficult to push

Possible Causes

 

Remedies

 

Incorrect Height adjustment 

 

Adjust Powerfoot to correct height setting

Visible dirt escaping from cleaner 

Possible Causes

 

Remedies

 

Dirt Container full 

 

Empty Dirt Container

 

Filter missing or installed incorrectly 

 

Check Upper Tank, Pre-Motor and 

 

 

 

Post-Motor Filters for correct installation

 

Dirt Container installed incorrectly 

 

Pull out and re-insert Dirt Container correctly

14

Troubleshooting

1

1

2

2

1

1

2

2

3

3

9

9

7

7

8

8

4

4

5

5

6

6

10

10

 WARNING: 

To reduce the risk of injury from 
moving parts and/or electrical 
shock, turn Power Switch OFF and 
disconnect plug from electrical 
outlet before performing trouble-
shooting checks.

1

1

2

2

1

1

3

3

1

1

2

2

3

3

ug603-5570_3760E_1105.indd   14

ug603-5570_3760E_1105.indd   14

2/2/06   4:12:21 PM

2/2/06   4:12:21 PM

Summary of Contents for Lift-Off REVOLUTION 3760 SERIES

















Reviews: