background image

Measuring cup

Your deep cleaner is equipped with a measuring 

cup for adding the proper amount of formula  

to the 2-in-1 water tank. For convenience the 

measuring cup is built into the lid of the 2-in-1 

water tank.

2-in-1 water tank

Our 2-in-1 water tank system is designed with 

a heavy duty bladder inside for clean water. As 

you clean, the clean water and formula in the 

bladder will empty. Dirty water pulled out of 

your carpet will collect around the outside of the 

bladder so clean and dirty water are always kept 

separate. This allows the user to maximize tank 

space, yet only carry one tank to and from the 

sink for emptying and filling.

Removable Nozzle

Cleaning up your machine after you’re done  

has never been easier! Nozzle pops off for  

rinsing in the sink.

Before you clean

1. 

Plan activities to give your carpet time to dry.

2. 

Move furniture to another area if cleaning an  

entire room (optional).

3. 

Vacuum area with a dry vacuum cleaner 

before  

deep cleaning.

4. 

Plan your cleaning route to leave an exit path.  

It is best to begin cleaning in the corner farthest  

from your exit.  

5. Pretreating

 (optional)

Pretreating is recommended to improve clean-

ing effectiveness for heavily soiled carpet in high 

traffic  

areas such as entry ways and hallways.
To pretreat:
 

 

a. 

Using the BISSELL Stain PreTreat,  

generously spray evenly over soiled area,  

do not overwet.

 

 

b. 

Wait 3-5 minutes before deep cleaning.

 

 

c. 

Clean as normal using your BISSELL  

deep cleaner.

Operations

   

   www.BISSELL.com

ATTENTION

Some Berber carpets have a tendency to fuzz with wear. 

Repeated strokes in the same area with an ordinary 

vacuum or deep cleaner may aggravate this condition.

7

Measuring Cup

Carry 

Handle

2

4'

3'

1

3

4

5

6

7

9

10

11

12

EXIT

START

HERE

Summary of Contents for CLEANVIE PROHEAT 46L5-F





















Reviews: