Bisque Paramount ME Replacement And Troubleshooting Download Page 13 | Manualshive

Page: 13 / 14

background image

Revision 2.0

make note of the slotted hole (on the top side here) and the pivot point (created by the
bottom mounting screw).

Figure 13: Removing the two screws that mount the speed reducer and motor assembly.

Figure 14: The right ascension homing sensor housing is now accessible for cleaning, removal and

replacement.

When the two sensor housings have been removed assemble the new sensors. Then the
two units can easily be re-installed.

«
...
11
12
13
14
»

Summary of Contents for Paramount ME















Reviews:

No comments

Related manuals for Paramount ME

Brand: Samsung Pages: 21

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

Brand: Panasonic Pages: 242

Brand: LAZER Pages: 13

Brand: neno Pages: 54

Brand: Metra Electronics Pages: 2

Brand: SICK Pages: 184

Brand: Compass Pages: 16

Telaire Ventostat T8100 NS Series

Brand: Amphenol Pages: 4

B-TRK502-02-01-SL

Brand: SRC Pages: 4

Brand: San Jamar Pages: 2

Brand: Toro Pages: 24

Efector 200 OGE08 Series

Brand: IFM Pages: 3

Brand: Zamel Pages: 12

Brand: Toro Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands