Bird Electronic Thruline 4020 Series Instruction Book Download Page 38

Page: 38 / 59

RS-232 Interface

Device Dependent Commands

The device-dependent commands used by the 4421 Power Meter are listed in

Table 6-16, organized by category.

Table 6-16 RS-232 Device Dependent Command Summary

orward

arrier Wave

(FC)

orward

(FD)

eflected

arrier Wave

(RC)

eflected

(RD)

Function

Selects forward or reflected RF power measurement mode.

Remarks

Measurement results are returned in Watts or dBm.

tanding

ave Ratio

(SW)

eturn

oss

(RL)

Function

Selects SWR or return loss match measurement mode.

Remarks

Measurement results are returned in VSWR or dB.

Category

Command

Description

Measurement

Forward carrier wave

Forward dBm

Reflected carrier wave

Reflected dBm

Standing wave ratio

Return loss

Minimum value

Maximum value

Range

RYY

Auto range on

R00 to R17

Manual ranges

RNN

Auto range off, stay at present range

Terminators

Two terminators: CR, LF

One terminator: CR

No terminator

Prefixes

Prefix YES

Prefix NO

Triggers

Continuous on ENT

One shot on ENT

One shot on TRG

One shot on measurement command

Status

Send back current machine state

Send back error conditions

Send back revision levels

Self-Test

Run self-test

Writable Store

WXXXXXX

Place XXXXXX in RAM

Summary of Contents for Thruline 4020 Series




























































Search results

Summary of Contents for Thruline 4020 Series

Reviews:

Related manuals for Thruline 4020 Series

Brands by name

Popular brands

Bird Electronic Thruline 4020 Series, Instruction Book

Search results

Summary of Contents for Thruline 4020 Series

Reviews:

Related manuals for Thruline 4020 Series

Brands by name

Popular brands