Bird Electronic Thruline 4020 Series Instruction Book Download Page 22

Page: 22 / 59

Bird 4421 RF Power Meter

Interface Capabilities

Table 5-4 IEEE-488 Interface Module Capabilities

Indicators

The bottom line of the power meter’s display shows indicators describing the

status of the Bird 4421 when used with the IEEE interface. These are:

REMOTE -

When REMOTE is displayed, the power meter is being controlled

through the interface. Measurements, units of measure, and certain other

parameters may be changed from a remote location.

LISTEN -

When LISTEN is displayed, the power meter is receiving data.

TALK -

When TALK is displayed, the power meter is transmitting data. This

is always shown when the unit is in “talker-only” mode.

LOCAL LOCKOUT -

When LOCAL LOCKOUT is displayed, the push buttons

are disabled and the power meter’s functions are being remotely controlled.

Setup

Dip Switch

Set the interface to ADDR (Addressable) by positioning DIP switch 1 to ON.

This makes the 4421 respond to controller commands.

Note:

There are several button styles on DIP switches (slide, rocker,

lever). Examine the DIP switch to determine the ON and OFF positions.

Set the primary address using the DIP switches. The primary address is fac-

tory set to 6, but can be set to any value between 1 and 31 (0 is reserved for

the controller) To set the primary address, turn OFF switches 4 – 8 so that the

sum of the bits turned off equals the desired primary address. In Figure 8

below, the address is set to 6 (the off switches have values of 4 and 2).

Figure 8 IEEE Interface Default DIP Switch Settings

Code Name

Description

SH1

Source Handshake Can handshake data or command bytes when the unit is

acting as a source.

AH1

Acceptor

Can handshake the bus when it is acting as the acceptor of
data or commands.

Talker

Can send data over the bus to other devices. This capability
exists only after the instrument has been addressed to talk, or
after a reading in talk-only mode.

Listener

Can receive device-dependent data over the bus. This capability
exists only after the unit has been addressed to listen.

SR1

Service Request

Can request service from the controller.

RL1

Remote-Local

Can be placed in remote or local mode.

PP0

Parallel Poll

Does not have parallel polling capability.

DC1

Device Clear

Can be reset to factory settings.

DT1

Device Trigger

Can have its readings triggered.

Controller

Does not have controller capability.

Bus Driver Type

Has open-collector bus drivers.

TE0

Extended Talker

Does not have extended talker capability.

LE0

Extended Listener

Does not have extended listener capability.

Note:

The primary address is used by the

controller to refer to specific devices on the bus.

When programming the controller, the address in

the program must be the same as the address set

on the interface module. Each device on the bus

must have a different primary address.

Summary of Contents for Thruline 4020 Series




























































Search results

Summary of Contents for Thruline 4020 Series

Reviews:

Related manuals for Thruline 4020 Series

Brands by name

Popular brands

Bird Electronic Thruline 4020 Series, Instruction Book

Search results

Summary of Contents for Thruline 4020 Series

Reviews:

Related manuals for Thruline 4020 Series

Brands by name

Popular brands