Biosonic Suvi Premier, Owner'S Manual

Page: 19 / 36

Premier / Premier Plus
19
Operating Instructions
4.2 How to use the Premier / Premier Plus Scaler
The side of the tip-end shall be applied to the tooth so that the movement of the tip is parallel to the
surface of the tooth. The first 2 mm of the tip are the most efficient. Place the tip on the tooth sur-
face before activating the foot control pedal. The power is regulated with the foot control pedal from
0 to 100% within each working mode.
Normal scaling rarely requires more than 50% power level of each working mode.
However, hard to remove calculus might require a higher power setting.
Normal scaling rarely requires more than 50% power level.
However, hard to remove calculus might require a higher power
setting.
The tip is normally aimed towards the toothpocket.
With the correct power setting, appropriate pressure against
the tooth (approx. 20 grams but not exceeding 50) and the tip
operating parallel to the surface, treatment will be gentle, quiet
and efficient.
If, during the treatment, a squeaking sound is heard (loud and
dominating), the pressure against the tooth might be too low
or the tip not parallel to the surface of the tooth.
To keep the tip working parallel
to the surface of each tooth, it is
important to follow the anatomy
of the tooth.
How to use the scaler
The side of the tip-end shall be applied to
the tooth so that the movement of the tip
is parallel to the surface of the tooth. The
first 2 mm of the tip are the most efficient!
Place the tip on the tooth surface before
activating the foot switch.
Ensure that contact between
the tip and the tooth surface
is maintained during scaling.
Keep moving the tip slowly
back and forth and let the
instrument do the work.
Use short and long strokes
so that the whole surface of
each tooth is scaled.
Normal scaling rarely requires more than 50% power level.
However, hard to remove calculus might require a higher power
setting.
The tip is normally aimed towards the toothpocket.
With the correct power setting, appropriate pressure against
the tooth (approx. 20 grams but not exceeding 50) and the tip
operating parallel to the surface, treatment will be gentle, quiet
and efficient.
If, during the treatment, a squeaking sound is heard (loud and
dominating), the pressure against the tooth might be too low
or the tip not parallel to the surface of the tooth.
To keep the tip working parallel
to the surface of each tooth, it is
important to follow the anatomy
of the tooth.
How to use the scaler
The side of the tip-end shall be applied to
the tooth so that the movement of the tip
is parallel to the surface of the tooth. The
first 2 mm of the tip are the most efficient!
Place the tip on the tooth surface before
activating the foot switch.
Ensure that contact between
the tip and the tooth surface
is maintained during scaling.
Keep moving the tip slowly
back and forth and let the
instrument do the work.
Use short and long strokes
so that the whole surface of
each tooth is scaled.
Ensure that contact between the tip and the tooth surface is maintained during scaling.
Keep moving the tip slowly back and forth and let the instrument do the work. Use short
and long strokes so that the whole surface of each tooth is scaled. The tip is normally
aimed towards the toothpocket.
To keep the tip working parallel to the surface of each tooth, it is important to follow
the anatomy of the tooth. With the correct power setting, appropriate pressure against
the tooth (approximately 20 grams but not exceeding 50) and the tip operating paral-
lel to the surface, treatment will be gentle, quiet and efficient. If, during the treatment,
a squeaking sound is heard (loud and dominating), the pressure against the tooth might
be too low or the tip is not parallel to the surface of the tooth.
4.3 After Treatment
Automatic cleaning function
1. Make sure the water control is fully open. Place the scaler handpiece
over the cuspidor bowl or sink and start the cleaning cycle by press-
ing the cleaning key “C”.
2. The cleaning cycle starts and stops automatically after 80 seconds.3.
After the cleaning cycle is finished, screw off the tip, counter
clockwise, with the torque wrench.
Note
Always set the water flow to
fully open before running the
cleaning cycle (dots in line,
see picture).
6
Safety notices in this manual
Warning indicates a potentially
dangerous situation. Non-observ-
ance may lead to death or injury.
Caution indicates a potentially
harmful situation. Non-observ-
ance may damage the equipment.
Note indicates a situation where
special notice should be ob-
served.
WARNING
Caution
Note