S Auto reset : when enabled, any color, dimmer or speed overrides will be reset each time the scene is changed
S Trigger : sets the scene triggering mode. Time Delay and Scene Butt allow for scenes to be scrolled through without playing
Auto : the scene will be triggered as soon as it’s selected
Time Delay : a short delay is added before a scene is triggered
Scene Butt. : the selected scene will not play until the scene button is pressed
First Start (F) : Default settings when the unit is first powered up
F Scene Nr. : specify a default scene number
F Scene Scene Recover : activates the previously playing scene
F Display Time : when enabled, the time will be displayed on the screen at startup
F Scene Nr. : enables the triggering of a scene at startup. If disabled, no scene will be triggered
Trigger (T) : Manages the controllers external triggering properties
T Time enable : enables the clock triggering
T Ports enable : enables the 8 dry contact ports
T RS232 enable : enables scene triggering by RS232
T IR enable : enables the infra red port (disabled by default to prevent interference)
T UDP enable : allows the controller to send and receive UDP messages required for network control
T Blackout port : enables the blackout relay output which is triggered when the stanby putton is touched
Ethernet (E) : Manages the controllers network settings
Ethernet : Enables the Ethernet socket on the controller
Dynamic IP Addr : enables dynamic IP addressing (DHCP) which allows the controller to obtain an IP address from a router
Sync Blackout: when this open is enabled, all other controllers on the network will go into standby when the standby button is
pressed
Enable NTP : enables Network Time Protocol. The controller will synchornise the clock with the internet if a connection is
evailable
NTP Server : the IP address of the server to synchronize the clock. The default is 005.135.141.108
Device’s IP Add : the controllers static IP address it will use if it does not receive an IP address via DHCP
Mask: the subnet mask of the controller if not set to DHCP. Generally this is 255.255.255.0
Default Gateway : the IP address of the router if not set to DHCP
MAC Address : a unique ID used to identify the controller on the network
Date/Time (D) : Manages the date and time stored inside the controller
Date : the controllers date
Time : the controllers clock time
G Bright normal : the % brightness when the controller is not sleeping G Bright sleep: the % brightness when the controller is
sleeping
G Bright LED : the % brightness of the mode and reset LEDs
Graphics (G) : Screen management
G Image enable : allows for images to be shown for each scene if they have been assigned in the programming software
G Image full : when enabled, the image will be displayed in full screen and the scene and area will not be visible
G Image time : the time it takes before the image is displayed in full screen
G Sleep enable : when enabled, the screen brightness will dim after a certain amount of time
G Sleep time : the amount of time to wait before sleeping
G Bright normal : the brightness of the screen’s backlight
G Bright sleep : the brightness of the screen’s backlight whilst the controller is sleeping
G Bright LED : the brightness of the scene, undo and standby LED’s
DMX Output (X) : Manage the timings of the DMX output messages and the page priorities (advanced function!)
X MBB : Mark Before Break- the time to wait between sending each 512 channel DMX message (or ‘packet’)
X Break : Break- the time to wait just before sending a new packet, resetting the DMX line
X MAB : Mark After Break- the message which tells your receiver to begin reading data
X MBS : Mark Between Slots- the delay time between sending each DMX channels data within the DMX packet
Univ-1/Univ-2 : each timing can be set differently depending on the universe number
X Alphab Mode : if the same scene is triggered in the global area and a second area, the area with the highest letter will take
priority
X LTP Mode : If the same scene is triggered in the global area and a second area, the latest scene triggered takes priority
Sensitive (S) : Manage the touch sensitivity settings
S USB Init : reset the touch sensitivity when the USB is connected and disconnected
S Auto Time : the time to wait before automatically resetting the touch sensitivity
S High Sense : when enabled, the sensitivity will be increased
S See Values : see each touch sensitive button number and palette value
www.biontechnologies.com | 9
