background image

5

User Enrollment

3.6 Enroll Pass Code User

PRESS:

 

1 + # + Master Code + 3 digit User ID + #

NOTE: At this point the scanner will light up. 

FIRST SCAN:

 Place the 1st finger on the scanner and remove when 

scanner light turns off.  

SECOND SCAN:

 Replace the same finger when scanner lights up for the 

second time.  You will hear a single beep if the enrollment is successful.

REPEAT:

 To add another finger for this user or any other users please 

repeat the process stated above. A fingerprint ID# can NOT be the same 
as a pass code ID#.

Example: Fingerprint User ID= #200 and Pass Code User ID= #300

PRESS:

 

1 + * + Master Code + 3 Digit ID + New 8 Digit 
Pass Code + Repeat New 8 Digit Pass Code + #

NOTE: A pass code ID# can NOT be the same as a fingerprint ID#.

HINT:

 When successful the lock will make a solid single beep.  If 

unsuccessful it makes 3 quick beeps.

HINT:

 When entering the codes take a 2-3 second short pause between 

codes. 

Example: Master Code (pause) ID# (pause) New Code (pause) Repeat New 
Code

When the new pass code is enrolled, close the slide cover , open it up & 
try the code to confirm your new code is working.

3.5 Enroll Fingerprint Users with User ID’s

BioBolt

®

 evo3 Biometric Deadbolt

http://www.bioboltlock.com | Intelligent Biometric Controls, Inc. | v1.1

Summary of Contents for evo3
















Reviews: