manualshive.com logo in svg

Bio-Science CI-900, Operation Manual, Page: 68 / 94

Share
Download
Bio-Science CI-900 Operation Manual Download Page 68

CI-900 Instruction Manual 8/10/2015 

 

1554 NE 3

rd

 Ave, Camas, WA 98607, USA              Phone: (360) 833-8835

 

 

sales@

cid-inc

.com

                 

       

                              www.cid-inc.com

                               63 

 

 

 

CI-900 Firmware Update Procedure 

1.

 

After installing the driver, open the 

CI-900 Firmware 

Upgrade 

application: “Transfer Code to CI-203 or CI-

900.” 

2.

 

If device is on, press power button to power off the 
device. 

Hold the down arrow button, then press power 

button.

 

The device's internal green LED near USB 

port/SD card should start flashing quickly. The device 
must be unplugged for this to work.  

3.

 

Select File and Open. 

4.

 

Navigate to the 

CI-900-ver-x.xx.bin. 

This is the code for 

the instrument.  

5.

 

Follow the instructions in the software to hold down the 
power button.  

6.

 

Release the power button when instructed. 

7.

 

Wait for the flash to be erased and then written. When the firmware transfer is complete, 
the software will indicate reset sent, followed by “leaving open”. The CI-900 will power off. 

8.

 

Power on the CI-900 and check the firmware version at 
the top of the display. The Transfer Code software 
application will indicate that no instrument is found, if 
the CI-900: 

 

is not connected to the computer 

 

is not powered on 

 

driver is not properly installed  

 

 

If this message is seen, make sure: 

 

the CI-900 is connected via mini-USB 

Summary of Contents for CI-900































































































Reviews:

No comments