“The phone does
not ring“
Check that the RINGER ON/OFF switch on the side of the
handset is set to ON.
Check that the total REN value of all equipment connected to
your telephone line is no more than 4 (see page 4). Disconnect
one or more telephones and see whether that helps.
“I can‘t store phone
numbers in memory“
Make sure the handset has no Dial tone and the In Use light is
off before you try to store numbers.
Do not pause for more than 30 seconds between pressing
buttons when storing a number.
“I hear ‘beeps’
during a call.”
Move closer to the main base unit within 20 seconds.
Otherwise your call may be cut off.
Press
to change channels.
Check whether the ‘battery low’ symbol is shown on the
display. If so, place the handset on the base unit or charger
pod to recharge the battery.
“There is interference
and noise on the
line.”
Move closer to the main base unit.
Try a different position for the base unit — perhaps higher.
Make sure neither the base unit nor the handset are near any
other electrical equipment.
Press
to change channels.
“The handset‘s
battery is running
low within an
hour or two.”
Before you first used the handset, you should have left it on the
base unit or charger pod for 12 hours to charge the battery fully.
Leave the handset off the base unit or charger pod until the
‘Battery Low’ light flashes. Then replace it and leave it for
12 hours (e.g. overnight). Repeat these two steps from time
to time — this will ensure that the battery becomes charged
to its full capacity.
If the problem persists, you may need to replace the battery
pack. To find out how to obtain a replacement, call the
Binatone Spares Department
on
01325 304 473
, between
9.00 am and 5.00 pm, Monday to Friday.
TROUBLESHOOTING
14
“Last Number Redial
and/or memory
dialling don’t work
on a PBX.”
When you first make a call, try pressing
for a pause
between the outside line access digit (e.g. 9) and the tele-
phone number. You should later be able to redial the number
using the
button.
When storing numbers in memory, you can include the
outside line access digit (e.g. 9) with each number.
If your PBX requires you to wait for a second Dial tone before
dialling the telephone number, press
for a pause
between the access digit and the number.
If the fault
persists …
u
Disconnect all other instruments connected to the same line
as the Pegasys 8 Triple and see whether you can make a call.
u
Disconnect the base unit from the telephone line and plug a
different phone into the master telephone socket. Try making
a call. If this works, the line is OK.
u
If the call does not work, and you are using a two-way socket
adapter, remove it and plug a telephone directly into the
socket. If the call now works, the adapter may be faulty.
u
If you cannot make a call, the fault may be on the exchange
line. Contact the service provider (the BT engineers on 151,
or your cable company).
u
If you still cannot identify the cause of the problem, contact
the
Binatone Help Line
on
0208 344 8870
. The Help Line is
open from 9.00 am to 5.00 pm, Monday to Friday.
Replacing the
batteries
When replacing the batteries in the handsets, refer to the
diagram on page 6.
Safety warnings
u
Never try to recharge alkaline batteries — they may burst,
causing injury or damage.
u
Use only the battery pack recommended by the Binatone
Spares Department.
u
Dispose of used batteries safely — never burn them, or put
them where they could get punctured.
TROUBLESHOOTING
Binatone Help Line: 0208 344 8870, 9.00 am to 5.00 pm, Monday to Friday
15
Summary of Contents for Pegasys 8 Triple
Page 11: ...20 ...
