Part No. 350245 Form No. F021604A
Page 12 of 12
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Engine stalls or labors when raking.
Raise blades so that they just touch the ground on a
level surface.
Solution
Possible Cause
Problem
Blades set too deep into ground
20
Engine Service and Warranty
Contact your nearest engine manufacturer's
authorized servicing dealer. (See page 7)
22.1
22
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON / LEE'S SUMMIT, MO 64082-2312 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
www.billygoat.com
WARRANTY PROCEDURE
Purchased
from
Purchase
Date
21
Serial Plate
R
ecord your machine model, serial number and
date-of-purchase and where purchased
R
min
-1
1803 S. Jefferson
Lee's Summit,
MO 64062 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model
Serial No.
Unit(Weight)
Engine Power
lbs.
kg
kW
rpm
Abnormal vibration.
Engine will not start.
Engine is locked, will not
pull over.
Debris locked against reel, or drive pulleys. Engine
problem.
Check stop switches, throttle, choke position and
gasoline. Connect spark plug wire. Clean or replace
air cleaner. Contact a qualified service person.
Stop work immediately. Replace any damaged or
missing blades. Tighten all loose bolts and nuts.
Damaged or missing blades. Loose handle bolts.
Loose engine bolts
Stop switch off (Honda only). Throttle in off position.
Engine not in full choke position. Out of gasoline. Bad
or old gasoline. Spark Plug wire disconnected. Dirty air
cleaner. Engine oil level too low (Honda only).
Pull spark plug wire and remove debris. Contact an
engine servicing dealer for engine problems.
MODEL NO.
GENERAL ENGINE SPECIFICATIONS
HORSEPOWER
ENGINE
HONDA
5.0
GC160AQHA
GOVERNED RPM
3600
ENGINE
When servicing engine refer to specific manufacturers engine
owner's manual. All engine warranty is covered by the specific
engine manufacturer. If your engine requires warranty or other
repair work contact your local servicing engine dealer. When
contacting a dealer for service it is a good idea to have your engine
model number available for reference(See table page above). If
you can not locate a servicing dealer in your area you can contact
the manufacturers national service organization.
To reach:
American Honda:
800-426-7701
Never store engine indoors or in enclosed poorly ventilated
areas with fuel in tank, where fuel fumes may reach an open flame,
spark or pilot light, as on a furnace, water heater, clothes dryer or
other gas appliance.
If engine is to be unused for 30 days or more, prepare as follows:
Remove all gasoline from carburetor and fuel tank to prevent
gum deposits from forming on these parts and causing possible
malfunction of engine. Drain fuel outdoors, into an approved
container, away from open flame. Be sure engine is cool. Do not
smoke. Run engine until fuel tank is empty and engine runs out of
gasoline.
NOTE:
Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing
the formation of fuel gum deposits during storage. Add stabilizer to gasoline in
fuel tank or storage container. Always follow mix ratio found on stabilizer
container. Run engine at least 10 min. after adding stabilizer to allow it to reach
the carburetor.
UNIT STORAGE
R
99 dB
Should a Billy Goat Machine fail due to a defect in material and/or
workmanship, the owner should make a warranty claim as follows:
-The Machine must be taken to the dealer from whom it was purchased
or to an authorized Servicing Billy Goat
Dealer
.
-The owner must present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
-The Warranty Claim will be completed by the authorized Billy Goat
Dealer and submitted to their respective Billy Goat Distributor for their
territory. Attention: Service Manager. Any parts replaced under
warranty must be tagged and retained for 90 days.
-The distributor service manager will sign off on the claim and submit
it to Billy Goat for consideration.
-The Technical Service Department at Billy Goat will study the claim
and may request parts to be returned for examination. Billy Goat will
notify their conclusions to the distributor service manager from whom
the claim was received.
-The decision by the Quality / Service department at Billy Goat to
approve or reject a Warranty claim is final and binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model & Serial
Number which are printed on the Billy Goat Serial Plate (See owner’s manual).
