background image

BIJUR DELIMON INTERNATIONAL

(919) 465 4448 

LOCAL   

(800) 631 0168 

TOLL-FREE   

(919) 465 0516 

FAX   

WWW.BIJURDELIMON.COM

2100 Gateway Centre Blvd., Suite 109   
Morrisville, NC 27560

35994  •  R2 

08/15

4

Clean or Replace the Upper Valve

1.  Unthread and remove the foot valve tube (61) from the pump tube (50) and take out the 

connection rod (52) together with the high pressure piston (56).

2.  Gently push out the packing assembly (57-60) from the pump tube (50) using a ø19mm tube and 

clean it carefully, replace any if damaged.

3.  Remove the pin that holds the connection rod (52) to the high pressure piston (56) and unthread 

the piston. Take out the components of the upper valve (53-55) and clean them carefully, replace 
any if damaged.

4.  Assemble the pump following the previous instructions, reversing each step.

Troubleshooting

Symptom

Possible Cause

Remedy

The pump is not working or 
there is no grease delivery.

Not enough air supply pressure.

Slowly increase the air supply 
pressure.

Some outlet line component is clogged or 
closed.

Clean or open the outlet circuit.

There are air pockets in the grease inlet 
area.

Stir and compact the grease.

The pump begins to operate very fast.

The drum is empty or the grease level is 
beneath the suction tube inlet.

Replace the drum or lower the 
suction tube until the inlet reaches 
below the grease level.

The pump runs on continuously 
after the grease outlet is closed.

There is a grease leak in some point of 
the outlet circuit.

Verify and tighten or repair.

Grease is leaking through the 
outlet muffl er.

Grease has by-passed to the air motor 
caused by worn or damaged packing set.

Replace the worn or damaged parts.

Air is leaking through the 
outlet muffl er.

The O-rings of the distributor axle (21) or 
the bushings (16) are worn or damaged.

Replace the axle assembly (21) and/
or bushing assembly (16).

The inverter O-rings are worn 
or damaged.

Replace the inverter O-rings.

Decrease of the grease delivery.

Dirt in upper valve or the foot valve.

Dismount and clean, replace 
if damaged.

Dirt in muffl er (18).

Dismount and clean/replace muffl er.

How to Order

Description

Drum Size

Part #

DP33 Pump

120 lb

F332

400 lb

F334

When ordering, specify by name, description and part number, e.g. DP33 Pump, 120 lb Drum, 
Part #F332.

  

Refer to page 5 for parts reference.

Before starting any kind of maintenance 
or repair, disconnect the compressed air 
supply and open a downstream valve to 
relieve the grease pressure. 

Summary of Contents for DP33








Reviews: