BFE Esprit ET188 Owner'S Manual Download Page 6

                                                                                                                                                                                               

ET188

 

 
 
 
 

 

 

NEVER 

operate this treadmill without reading and completely understanding the results of any 

operational change you request from the computer. 

 

Understand that changes in speed and incline do not occur immediately. Set your desired 
speed on the computer console and release the adjustment key. The computer will obey the 
command gradually. 

 

NEVER 

use your treadmill during an electrical storm. Surges may occur in your household 

power supply that could damage treadmill components. 

 

Use caution while participating in other activities while walking on your treadmill; such as 
watching television, reading, etc. These distractions may cause you to lose balance or stray 
from walking in the center of the belt, which may result in serious injury. 

 

NEVER 

mount or dismount the treadmill while the belt is moving. the treadmills start with at a 

very low speed and it is unnecessary to straddle the belt during start up. Simply standing on 
the belt during slow acceleration is proper after you have learned to operate the unit. 

 

Always hold on to a handrail or hand bar while making control changes (incline, speed, etc.). 

 
 
 

A safety tether cord is provided with this unit. It is a simple magnetic design that should be used at 
all times. It is for your safety should you fall or move too far back on the tread-belt. 
Pulling this safety tether cord will stop tread-belt movement. 
 

To Use: 

1. Place the magnet into position on the round portion of the console control head. Your treadmill 
will not start and operate without this. Removing the magnet also secures the treadmill from 
unauthorized use. 
 
2. Fasten the plastic clip onto your clothing securely to assure good holding power. 

Note: 

The 

magnet has strong enough power to minimize accidental, unexpected stopping. The clip should be 
attached securely to make certain it does not come off. Be familiar with its function and limitations. 
The treadmill will stop, depending on speed, with a one to two step coast anytime the magnet is 
pulled off the console.   

Safety Tether Cord

 

Important Operation Instructions

 

Summary of Contents for Esprit ET188


















Reviews: