16
6.3 Using the device on your back
1. Sit in a comfortable position.
2. If you wish, you can place the hygienic cover
7
over the device for hygiene reasons.
3. Place the device between the back rest and your back (see figure
C
).
You can place the device higher or lower depending on which part of your back you want to massage.
4. Press the ON/OFF button
6
to switch on the device.
The ON/OFF button
6
will start to light up green and the massage heads
1
will begin to rotate. At the
beginning, the device intensity is always preset to low (green) and the heat function is always deactivat-
ed. Further information on the individual settings options can be found in chapter “6.4 Settings options”.
5. The massage should feel pleasant and relaxing at all times. If the massage is painful or uncomfortable,
stop the massage or change the position of your back or the contact pressure.
The device has an automatic switch-off function. It switches off automatically after 15 minutes
of operation.
6. To end the application manually, press the ON/OFF button
6
again.
The ON/OFF button
6
will go out and the massage heads
1
will stop.
6.4 Settings options
Direction of rotation of the massage heads
The massage heads on the device can rotate either to the left or right.
• To change the direction of rotation of the massage heads, press the mode button ( )
5
with the
device switched on.
Intensity of the massage heads
You can adjust the intensity of the massage heads on the device.
• To adjust the intensity, press the intensity button ( )
4
with the device switched on (green = low,
blue = medium, red = high).
Switching on the heat function
The device has a heat function. If the heat function has been activated, the massage heads will become
pleasantly warm during the application.
1. To switch on the heat function, press the heat button ( )
3
with the device switched on. The heat but-
ton ( )
3
will start to light up red.
2. Press the heat button ( )
3
again to switch off the heat function. The button will no longer be lit red.
7. CLEANING AND MAINTENANCE
CAUTION
Always disconnect the device from the socket before cleaning it. Clean the device using only the methods
specified. Liquid must not penetrate the device or the accessories.
1. Clean the device with a slightly damp cloth. If it is very dirty, you can also moisten the cloth with a mild
soapy solution.
2. Small marks can be removed using a cloth or damp sponge, and some liquid delicate laundry detergent
where necessary. Do not use any solvent-based cleaning products.
3. Do not use the device again until it is completely dry.
Washing the hygienic cover
1. Remove the hygienic cover
7
from the device.
2. Hand wash the hygienic cover
7
(max. 30 degrees).
Summary of Contents for FM 70
