background image

Control Panel Function

Safety, Alarms and Error Messages

Steam Function

The control panel is installed with 4 malfunction messages

Press the steam button to activate the steam, the symbol will 

E0

appear on the display

Issue

Steam generator does not shut down when set 

                      temperature is reached

Steam Adjustment

Issue

Steam generator shuts down before  set  temperature 

Press the steam time/temp adjustment button to change

                      is reached

the time period or steam temp

Solution - Failed sensor - Replace electric box and cables

E1 /E2

The pre-set time is 60 minutes

Issue

No steam created, as no water in the steam tank

The pre-set temp is 45c

E1 appears if no water enters tank for 2 minutes

Press this button then press + or - to adjust

Tank automatically tries to re-fill, if successful E1 disappears

The time settings available are 0 -120 minutes

Issue

E2 appears if attempt fails and the steam generator stops 

The temp settings available are  25 - 60c

Checks

Check water supply is reaching the steam tank
Check cable connections

When the set steam time has been reached the steam will

Check if inlet valve filter on the steam tank is blocked 

turn off.

Solution

Re-instate water supply to cabin.
Is water supply turned on, is there a blockage.

When the set steam temperature has been reached the steam

Re-connect cables if dis-connected or replace section 

will turn off

required, if unable to re-connect or a cable is damaged
Clear debris in inlet valve

An automated Ozone cleansing function will activate once the 

Replace steam generator if inlet valve failed

steam function has been turned off and run for approximately

E3

3 minutes.

Issue

E3 Message as soon as steam function is turned on.

Solution -  Turn OFF steam function and turn back on

If message is still present carry out E1 and E2 checks

Issue

E3 Message during steam function use and no steam

Solution -  Blown fuse in plug / Replace fuse

Loose connection / Check all wires and connectors
Turn off steam function, then:
Press re-set button on side of steam tank, then turn steam
function back on, if still present replace steam tank.

SEPT  18 - V6BB

Summary of Contents for 900 Quadrant Steam



















Reviews: