manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard Power Knife 109496, Operator'S Manual

Share
Download
BETTCHER INDUSTRIES Whizard Power Knife 109496 Operator'S Manual Download Page 7

Operating 

Bettcher Industries, Inc. 

Whizard® Power Knife Manual 

Instructions 

 

October 21, 2020 

Page 3 

 

 

SECTION 5.0  Unpacking 

 

5.1  Safety First 

 

 

 

 

5.2  Included With Your Machine 

The following parts are included with each Whizard® Power Knife. Please check when 
unpacking and advise your local Bettcher Industries representative if the delivery is incomplete. 

 

Head Assembly 

Motor Assembly 

30 VDC Power Supply 

Special Stone For Sharpening 

Special Steel For Sharpening 

Operating Instructions 

 

 

SECTION 6.0  Installation 

Please review and read all instructions carefully before attempting to use your Whizard® Power 
Knife. 
 
To use the Whizard® Power Knife, first 
provide a clear work area. Place the Power 
Supply in a clean, dry location near the 
vertical oven or broiler. Plug the power cord 
into an appropriate wall outlet. (Refer to the 
data plate on the power supply fuse 
enclosure cover for voltage information for 
your unit). Plug the Motor Unit into the 
power supply receptacle, lining up the 
locator tabs on both the cord and the receptacle 
as shown at right. Tighten the knurled fitting. 

 

WARNING 

SHARP BLADES MAY CAUSE CUT INJURY! 

UNPACK THE WHIZARD® POWER KNIFE CAREFULLY. 

Summary of Contents for Whizard Power Knife 109496

























Reviews:

No comments

Brands by name

Popular brands

Load more brands