Betec IceAge II Instruction Manual Download Page 6

   

Trouble Shooting 

   
Before   bringing   to   the   service   centre,   please   check   the   followings:   

 

 

Problems

 

Possible Reasons

 

Solution 

The   compressor   makes   
some   unusual   noise   when   
the   “Power   On   Indicator”   
is   “On”   

 

Incorrect   power   supply.

 

Unplug   the   unit,   and   check   to   ensure   
correct   power   supply   is   used.   

 

The   “Power   On   Indicator”   
does   not   light   

 

–   No   power   supply   
–   Bad   contact   with   the   
power   outlet   

 

Check   both   the   power   cord,   power   
plug   and   power   outlet   

 

The   “Ice   Full   Indicator”   
keeps   on   blinking

  

Ice   Baffle   are   blocked   by   
ice   cubes.   It   can   not   
works   properly   
   

 

Remove   the   ice   cubes,   turn   off   the   
ice   maker.   And   then   turn   on   again   

 

 

 
NOTE:   Please contact our service centre for replacement if problems are not caused by the 

above reasons. 

 
 
 
The unit is in normal good condition if the following occurred 
 

•   The   fan   is   still   running   for   few   seconds   after   switching   “Off”   the   unit   and   the   compressor.   
   
•   Noise   caused   by   the   running   compressor   and   the   flowing   refrigerant   inside   the   compressor.   

 

Summary of Contents for IceAge II








Reviews: