background image

24

E85263-00 August14S

1001 Brown Avenue  •  Toledo, Ohio  43607-0127 

Customer Service: 888-GO-BETCO  •  Fax: 800-445-5056  •  Technical Service: 877-856-5954  •  www.betco.com

10 year coverage

Subject to the conditions stated below, 

Betco warrants parts and labor on 

rotationally molded polyethylene tanks/

housings and injection molded vacuum 

head assemblies to be free from defects 

in materials and workmanship for 

a period of ten years to the original 

purchaser.

3 Year Coverage

Subject to the conditions stated below, 

Betco warrants parts and labor on all 

other Betco components to be free from 

defects in materials and workmanship 

for a period of three years to the origi-

nal purchaser.

1 Year Coverage

Subject to the conditions stated below, 

Betco offers a limited warranty on parts 

and labor on the following equipment:  

parts and accessories to be free from 

defects in materials and workmanship 

for a period of one year to the original 

purchaser.

•  HF14 Upright Vacuum: #E88820-00 
•  Bac Pac Lite Vacuum: #85903-00
• 

FiberPRO

®

 Floor Dryer: #85507-00 

•  WORKMAN

 Series Vacuums: 

#85024-00, #85025-00, #83012-00, 

#85027-00 

• 

All Tools and Accessories

• 

All Battery Chargers

• 

All Batteries are pro-rated for 1 year

Allowable Travel Time Warranty Reimbursement:

Eligible equipment: All battery and propane powered equipment products.  Warranty period: 90 days from date of sale to the 

original purchaser. A maximum 180 mile round trip at 50 cents per mile will be allowed for warranty consideration.

Propane Machine Warranty:

Kawasaki engines are warranted by Kawasaki for a period of 2 years against manufacturer defects. All other components 

(except wear items)*  are warranted by Betco for a period of 3 years.

*Wear Items exempt from Warranty consideration include but may not be limited to: power cords, transport wheels, 

vacuum bags, belts, squeegee blades, pad drivers, clutch plates, handle grips, filters, screens, throttle cables, brushes 

and carbon brushes.

Subject to the conditions and exceptions stated in this warranty, Betco warrants the Betco products to be free from defects in 

material and workmanship, under normal use and service, for the periods listed under the warranty policy to the original pur-

chaser. At any time during the warranty period, Betco will furnish replacement parts for the Betco parts to the original purchas-

er. Such parts will be furnished and charged including transportation costs, to the original owner through any Betco authorized 

Service Distributor. If the original part is returned within the warranty policy period from date of delivery for inspection by 

Betco and is found to be defective the owner will be credited for the cost of replacement parts plus shipping and handling. 

Replacement parts that have become defective through wear or abuse are not included in this warranty.

This warranty does not apply to damage or defect caused by accident, misuse. Negligence, fire, or to any Betco product which 

has been serviced or repaired by other than an authorized Betco Service Distributor or Betco factory personnel. This warranty 

is void if products are used for any purpose other than that which was intended. There are no other warranties expressed or 

implied. In no event shall Betco be liable for incidental or consequential damages or any damage to person or property. (Please 

note some states do not allow the exclusion or limitations for incidental and consequential damages).

BETCO US WARRANTY POLICY

Summary of Contents for CREWMAN

























Reviews: