SPECIFICATION
RSP-1500-5
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
WORKING TEMP.
ALARM SIGNAL OUTPUT
REMOTE ON-OFF CONTROL
AUXILIARY POWER
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
OVERLOAD
Note.5
OVER VOLTAGE
AC CURRENT (Typ.)
5V
240A
0 ~ 240A
1200W
150mVp-p
4.5 ~ 5.5V
±
2.0%
±
0.5%
±
2.0%
1500ms, 100ms at full load
10ms at full load
14ms at full load
16ms at full load
90 ~ 264VAC 127 ~ 370VDC
47 ~ 63Hz
80%
17A/115VAC 8A/230VAC
30A/115VAC 60A/230VAC
<2.0mA / 240VAC
105 ~135% rated output power
5.75 ~ 6.75V
Protection type : Constant current limiting unit will shut down o/p voltage after 5sec. Re-power on to recover
13.8 ~ 16.8V
17 ~ 20.5V
27.6 ~ 32.4V
31 ~ 36.5V
57.6 ~ 67.2V
Protection type : Shut down o/p voltage, re-power on to recover
Shut down o/p voltage, recovers automatically after temperature goes down
-20 ~ +70
(Refer to "Derating Curve")
℃
Please see the Function Manual.
Power OK signal. Please see the Function Manual.
[email protected](Only for Remote ON-OFF control)
20 ~ 90% RH non-condensing
-40 ~ +85
, 10 ~ 95% RH
℃
±
℃
℃
0.05%/
(0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
265.3K hrs min.
Telcordia SR-332 (Bellcore) ; 90.3K hrs min. MIL-HDBK-217F (25
)
℃
278*127*83.5mm (L*W*H)
3.0Kg; 4pcs/13Kg/1.19CUFT
87%
87%
90%
90%
91%
±
0.5%
±
0.5%
±
0.5%
±
0.5%
±
0.5%
±
0.5%
±
0.5%
±
0.5%
±
0.5%
±
0.5%
±
1.0%
±
1.0%
±
1.0%
±
1.0%
±
1.0%
150mVp-p
10 ~ 13.5V
150mVp-p
13.5 ~ 16.5V
150mVp-p
20 ~ 26.4V
150mVp-p
24 ~ 30V
200mVp-p
43 ~ 56V
12V
125A
0 ~ 125A
1500W
15V
100A
0 ~ 100A
1500W
24V
63A
0 ~ 63A
1512W
27V
56A
0 ~ 56A
1512W
48V
32A
0 ~ 32A
1536W
RSP-1500-12
RSP-1500-15
RSP-1500-24
RSP-1500-27
RSP-1500-48
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4.
The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on
a
mm*
mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.
720
360
For guidance on how to
perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
POWER FACTOR (Typ.)
0.95/230VAC 0.98/115VAC at full load
SAFETY STANDARDS
UL60950-1, TUV EN60950-1 approved
RIPPLE & NOISE (max.)
Note.2
VOLTAGE TOLERANCE
Note.3
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25
/ 70% RH
℃
ENVIRONMENT
SAFETY &
FUNCTION
EMC
(Note 4)
PROTECTION
OUTPUT VOLTAGE PROGRAMMABLE(PV)
Adjustment of output voltage is allowable to 70 ~ 100% of nominal output voltage. Please refer to the Function Manual.
CURRENT SHARING
Up to 6000W or (3+1) units. Please refer to the Function Manual.
Parameter
Parameter
ESD
Radiated
EFT / Burst
Surge
Conducted
Magnetic Field
Voltage Dips and Interruptions
Conducted
Radiated
Harmonic Current
Voltage Flicker
EN55024 , EN61204-3, EN61000-6-2
Standard
Standard
EN55022 (CISPR22) / EN55011 (CISPR11)
EN55022 (CISPR22) / EN55011 (CISPR11)
EN61000-3-2
EN61000-3-3
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11
Test Level / Note
Test Level / Note
Level 3, 8KV air ; Level 2, 4KV contact
Level 3
Level 3
Level 3, 2KV/Line-Earth ; Level 2, 1KV/Line-Line
Level 3
Level 4
>95% dip 0.5 periods, 30% dip 25 periods,
>95% interruptions 250 periods
Class B
Class A
-----
-----
EMC IMMUNITY
EMC EMISSION
REMOTE SENSE
Compensate voltage drop on the load wiring up to 0.3V. Please refer to the Function Manual.
1
5
0
0
W Single Output with PFC Function
MEAN WELL
RSP
-
1
5
0
0
SERIES
