11
TERMINAL BOARD CONNECTIONS:
CN1:
1 : 24 VAC/DC power supply input.
2 : 12 VAC/DC power supply input.
3 : 0 V power supply input.
CN2:
1 : Relay output OUT 1 clean control contact (NO).
2 : Relay output OUT 1 clean control contact (NO).
3 : Relay output OUT 2 clean control contact (NO).
4 : Relay output OUT 2 clean control contact (COM).
5 : Relay output OUT 2 clean control contact (NC).
6 : Mass input.
7 : Antenna hot pole input.
CN3:
1 : Power supply output 12 VDC Device.
2 : Communication port RS 485 signal A.
3 : Communication port RS 485 signal B.
4 : Power supply output 0 VDC device.
CN4 :
Connection for “INT 2292” interface.
INSTALLATION OF THE RECEIVER:
t is very important to choose the place of installation carefully in order for the transmitter and
the receiver to function well. Capacity is not only related to the device technical data, but also
varies depending on the site’s radio-electric conditions.
The receiver is equipped with a rigid wire section antenna. Connect an RG58 50 OHM coaxial
cable tuned antenna if wanting to increase sensitivity. Place the antenna externally in clearly
visible points and away from metal structures.
There must be a distance of at least 5 metres between the two receivers if installation is to
be successful.
OPERATING MODE WITH REMOTE CONTROLS
,
t
ag
r
eader
, K
ey
B
oard
and
/
or
nFC
r
eader
The receiver can be combined with Remote Controls, TAG Reader, Keyboard and/or NFC
Reader and stores up to 1000 different users. We recommend you write down the cor-
responding “storage position - user name”.
For use with remote controls, the receiver unit is equipped with an incorporated receiver;
for use with other devices, the desired accessory must be connected (by carefully fol-
lowing the connection diagrams described in the relative operating manuals) supplied
as optionals.
DATE/TIME SETTING
The receiver is equipped with a clock with buffer battery that allocates a time reference
to each operation.
Proceed as follows to enter the date and time:
Date settings:
use the UP or DOWN button to go to the
DATE
storage position and press SEL and SET:
Digits 2, 3 and 4 will start flashing, at the same time use the UP or DOWN button to
select a day of the week between MON and SUN then press SET to confirm (
STOR
will
be displayed); next, Digits 1 and 2 will start flashing, at the same time use the UP or
DOWN button to select a number between 01 and 31 to choose the day and press SET
to confirm (
STOR
will be displayed); next, Digits 3 and 4 will start flashing, at the same
time use the UP or DOWN button to select a number between 01 and 12 to choose the
month and press SET to confirm (
STOR
will be displayed); next, all Digits 1,2,3 and 4 will
start flashing, at the same time use the UP or DOWN button to select a number between
15 and 99 to choose the year and press SET to confirm (STOR will be displayed), thus
completing the operation.
Time settings:
use the UP or DOWN button to go to the
TIME
storage position and press SEL and SET:
Digits 1 and 2 will start flashing, at the same time use the UP or DOWN button to select
a number between 00 and 23 to choose the hour and press SET to confirm (
STOR
will be
displayed); next, Digits 3 and 4 will start flashing, at the same time use the UP or DOWN but-
ton to select a number between 00 and 59 to choose the minutes and press SET to confirm
(
STOR
will be displayed), thus completing the operation.
PROGRAMMING OF REMOTE CONTROLS,
t
ag
r
eader
, K
ey
B
oard
and
/
or
nFC r
eader
Programming of the Remote Controls, TAG Reader, Keyboard and/or NFC Reader is
the self-learning type and is performed as follows: use the UP or DOWN button to go
to the desired storage position (shown on the display from
0001
to
0999
) paying at-
tention to the KEYBOARD, NFC DEVICE, REMOTE CTR and TAG DEVICE LEDs since the
lighting up of one of these four means that the location selected is occupied. Press
SEL, all of the LEDs will start flashing and at the same time send the code with the
Remote Control or move the Transponder close to the TAG Reader or digit an access
code on the KEYBOARD or move the Smartphone close to the NFC Reader.
STOR
will
be displayed and the LED of the corresponding Device will switch from off to on, thus
completing the operation.
To delete a Device previously stored, using the UP or DOWN button go to the location of
the occupied storage position, press SEL, one of the four corresponding KEYBOARD, NFC
DEVICE, REMOTE CTR and TAG DEVICE LEDs will start flashing; press the SET button, the
