4
Requirements
1. Overhead clearances (Minimum values)
The minimum overhead clearances shall be in accordance with the minimum values indicated in the table
n.1 and are shown and in the fig. 1- 2
Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions.
However, in no case shall the clearance between the top of the highest burner of the cooking appliance and
the range hood be less than 25 ½”( 650mm).
Any other downward facing combustible surface less than 600mm above the top of the highest burner shall
be protected for the full width and depth of the cooking surface area.
However, in no case shall this clearance to any surface be less than 17
3/4
”(450mm.)
Maximum depth for the overheads cabinet is 13” (330mm)
2. Side clearances (Minimum values)
The different side clearances shall be in accordance with the minimum values indicated in the table n.1 and
are shawn and in the fig. 1- 2
The cooking surface area is defined as that part of the appliance where cooking normally takes place and
does not include those parts of the appliance containing control knobs.
Table n.1
Min. Clearances
inches (mm)
Min. Clearances
inches (mm)
L1
20”
(500)
L10
34
1/4
” (870)
L2
1
9/16
“ (40)
L11
36“ (915)
L3
2
3/4”
(70)
W
35
1/16
“ (890)
L4
18” (457)
D
20
1/2
“ (520)
L5
24” (610)
B1 (*)
2
3/8
“ (60)
L6
13” (330)
B2 (*)
6“ (152)
L7
36
1/2
“ (925)
B3 (*)
2
3/8
“ (60)
L8
1
9/16
“ (40)
B4 (*)
6“ (152)
L9
6
3/4
” (172)
(*) Note:
-B1 is the min. clearance between the front edge of the appliance and the front edge of the cabinet.
-B2 and B4 are the min. clearance between the left/right side edge of the appliance and the side wall (if
present).
-B3 is the min. clearance between the back edge of the appliance and the back wall.
Installation air exhaust
See table n.2 and fig. 3-4-5-6
Table 2
Min. Clearances
inches (mm)
Min. Clearances
inches (mm)
L15
15
12/16
”
(400)
L31
4
5/16
” (110)
L16
1
9/16
“ (40)
L32
1“ (25)
L19 (MAX)
1
9/16
“ (40)
K18
1
9/16
“ (40)
L22
4
5/16
” (110)
S18
2
9/16
“ (65)
L24
3
15/16
” (100)
S20
13/16
“ (20)
L28
8
11/16
” (220)
T8 (MIN)
1
15/16
“ (50)
L29
18
10/16
“ (473)
T15 (MIN)
1
3/16
“ (30)
L30
28
9/16
“ (725)
Summary of Contents for PM0JD2XE
