Berner BACHDD-1 BL, Original Instructions Manual, Page: 23 / 72

23 ENGLISH
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under “Technical Data” fulfi lls all the relevant provisions
of the directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC
and the following harmonized standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-1:2010
EN 55014-1:2017
EN 55014-2:2015
EN 50581:2012
Künzelsau, 2019-02-07
i.V. Bert Habets
Senior Director Continuous Improvements
Authorized to compile the technical fi le
Berner Trading Holding GmbH
Berner Straße 6
D-74653 Künzelsau
BATTERIES
New battery packs reach full loading capacity after 4 - 5 chargings
and dischargings. Battery packs which have not been used for
some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate for
about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the
battery could become to high. If this happens, the battery will shut
down.
Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
INTENANCE
Use only Berner accessories and spare parts. Should components
need to be replaced which have not been described, please
contact one of our Berner service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the ten-digit No. as well as the machine type printed on the
label and order the drawing at Berner.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work
on the machine.
Please read the instructions carefully before
starting the machine.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that have
reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
GUARANTEE AND GUARANTEE SERVICE
Each tool, spare part or accessory is consistently checked before
being dispatched from the manufacturing plant. If, despite this
fact, there are any defects, please send the item directly to our
Client Services Headquarters or to the nearest service repair
shop of the firm Berner.
The warranty period of 36 months for tools and 12 months for
batteries and chargers starts on the date of purchase which must
be verifi ed using the original receipt. During the guarantee period
the producer guarantees:
• free removal of possible defects;
• free replacement of all damaged parts;
• free professional servicing.
The requirement for this is that the problem is a material and/
or manufacturing fault. Defects or faults caused by incorrect
treatment or excessive force are not covered by the warranty.
Furthermore, only original accessory parts may be used, which
Berner has expressly identifi ed as suitable for the operation with
Berner machines.
You can fi nd out the location of your nearest customer service
workshop in the address list at the back of this document.
445 624 - Berner-BACHDD-1_BL_18V.indd 23 445 624 - Berner-BACHDD-1_BL_18V.indd 23 08.02.2019 08:52:59 08.02.2019 08:52:59