18
| English
1 609 92A 1DR • 19.8.15
Mounting/Replacing the Application Tool/
Accessory
If required, remove an already mounted application
tool/accessory.
For removing the application tool/accessory,
loosen the screw
11
with the hex key
12
and re-
move the application tool/accessory.
Mount the requested application tool/accessory
(e.g. plunge cut saw blade
10
) in such a manner on
the tool holder
8
that the offset faces downward
(see illustration on the graphics page; marking on
the application tool/accessory is readable from
above).
Turn the application tool/accessory to a position
favourable for the respective job, and allow it to en-
gage into the cams of the tool holder
8
. 12 different
positions are possible, each offset by 30 °.
For more intermediate positions, the adapter
13
(accessory) can be used: Allow the adapter to en-
gage with the smooth side onto the cams of the
tool holder
8
(see illustration on the graphics
page). Position the application tool/accessory onto
the adapter in any position.
Fasten the application tool/accessory with bolt
11
.
Tighten the bolt with hex key
12
until the spring
washer of the bolt faces flush against the applica-
tion tool/accessory.
Check the tight seating of the application
tool/accessory.
Incorrect or not securely fas-
tened application tools/accessories can come
loose during operation and pose a hazard.
Mounting/Replacing a Sanding Sheet on the
Sanding Plate
The sanding plate
14
is fitted with Velcro backing
for quick and easy fastening of sanding sheets with
Velcro adhesion.
Before attaching the sanding sheet
15
, free the Vel-
cro backing of the sanding plate
14
from any de-
bris by tapping against it in order to enable opti-
mum adhesion.
Position the sanding sheet
15
flush alongside one
edge of the sanding plate
14
, then lay the sanding
sheet onto the sanding plate and press firmly.
To ensure optimum dust extraction, pay attention
that the punched holes in the sanding sheet match
with the holes in the sanding plate.
To remove the sanding sheet
15
, grasp it at one of
the tips and pull it off from the sanding plate
14
.
You can use all sanding sheets, fleece pads/polish-
ing cloth pads of the Delta 93 mm series of Berner
accessory program.
Sanding accessories, such as fleece pads/polish-
ing cloth pads, are attached to the sanding plate in
the same manner.
Dust/Chip Extraction
Dusts from materials such as lead-containing
coatings, some wood types, minerals and metal
can be harmful to one’s health. Touching or
breathing-in the dusts can cause allergic reac-
tions and/or lead to respiratory infections of the
user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in con-
nection with wood-treatment additives (chro-
mate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– As far as possible, use a dust extraction sys-
tem suitable for the material.
– Provide for good ventilation of the working
place.
– It is recommended to wear a P2 filter-class
respirator.
Observe the relevant regulations in your country
for the materials to be worked.
Prevent dust accumulation at the workplace.
Dusts can easily ignite.
Connecting the Dust Extraction (see figure A)
For sanding, always connect the dust extraction.
Remove the application tool/accessory when
mounting the dust extraction
19
(accessory).
If required, assemble the parts of the dust extrac-
tion
19
as shown in the figure. Position the assem-
bled dust extraction onto the machine via the tool
holder
8
. Turn the dust extraction in such a manner
that the cams of the dust extraction engage into the
corresponding recesses on the housing. Fasten
the dust extraction to the machine with the retain-
ing clip
17
as shown in the figure.
Pay attention that the felt ring
16
is undamaged
and faces tightly against the sanding plate
14
.
Replace a damage felt ring immediately.
Place a vacuum hose
20
(accessory) onto the vac-
uum connection
18
. Connect the vacuum hose
20
with a vacuum cleaner (accessory).
The vacuum cleaner must be suitable for the mate-
rial being worked.
Scraper,
flexible*
Silicone and
other elastic
materials
Base plate for
sanding,
series Delta
93 mm*
Depends on
sanding sheet
Accessory
Material
* optional accessory
OBJ_BUCH-890-004.book Page 18 Wednesday, August 19, 2015 9:45 AM
