In accordance with current lens multiples auto adjust speed of rotation.
High speed domes support 8-channel alarm input and 2-channel alarm output (middle speed dome serials cameras
support 2-channel alarm-input and 1-channel alarm-output). 1# alarm matches with 101# preset position; 2# alarm
matches with 102# preset position; 8# alarm matches with 108# preset position. Any channel alarms, 2 channels relays
alarm; call 100# preset position, then relays stop outputting.
After settling start-point and end-point, scan begins with clockwise direction until to the end-point, then scan back
from end-point to start-point. By this way scanning till receiving any command (as sheet below):
Proportional speed-shift:
Alarm linkage:
(optional
function)
Point-to-point constant scanning:
Attached chart: command list for dome and camera (all dome models fitted)
Notes: ¤” means this function Available; “ N means Not Available
“
A ”
Preset Position
Number
Call Preset Positions
Set Preset Position
Dome/Camera Control Content
65
Run first route (Sequential scan of 1#~16# preset positions)
¤ NA
66
Run second route (Sequential scan of 17#~32# preset positions)
¤ NA
67
Run third route (Sequential scan of 33#~48# preset positions)
¤ NA
68
Run fourth route (Sequential scan of 49#~64# preset positions)
¤
NA
69
Run fifth route (Sequential scan of 101#~128# preset positions)
¤
NA
70
Run all sequential scans of confirmed preset positions
¤
NA
71
Clockwise 360°scan (low speed)
¤
NA
72
Clockwise 360°scan (middle speed)
¤
NA
73
Clockwise 360°scan (high speed)
¤
NA
74
Anti-clockwise 360°scan (low speed)
¤
NA
75
Anti-clockwise 360°scan (middle speed)
¤
NA
76
Anti-clockwise 360°scan (high speed)
¤
NA
77
Set duration time of preset position
¤
¤
78
Zero calibration
¤
NA
79
Mirror
Off
On
80
Screen Display
Off
On
81
Digital zoom
Off
On
82
Color
Off
On
83
Backlight compensation
Off
On
84*
Manually switch ICR
Off
On
85
Negative image
Off
On
86*
Auto switch ICR
Off
On
87
White balance mode
Manual
Auto
88
View state of dome
¤
NA
89
Exposure mode
Manual Auto
90
Focus mode
Manual Auto
91
Back to Factory Settings
¤
NA
92
Call menu
¤
¤
93
View version of dome
¤
NA
94
Eliminate single preset position (Once more within 5 seconds)
¤
NA
95
Eliminate all preset positions (Once more within 5 seconds)
¤
NA
96
Run linear scan / Set start of linear scan
¤
¤
97
Set end of linear scan
NA
¤
100
Shut alarm-output (be sure alarm-output exists)
¤ NA
Supplement:
Items
SONY
CANON
CNB SAMSUNG
Preset Position Range
1~255
1~128
1~255 1~255
Preset Position Lasting
(
Image Vertical-Flip(V-FLIP)
√
91 Command
√
92
#
command)
√
(77
#
command) ×
77
#
command)
Period Setting
×
×
×
#
×
√
×
×
77
#
detention-time setting is similar to 92#
Cautions:
This manual does not introduce setting methods of detail camera menus. If you want to change
camera parameters, please contact to dealer and ask for setting instructions of menus.
- 3 -
Set 92#, screen displays camera menu; call 92# or select EXIT button leaving menu. In menu state, WIDE, TELE,
NEAR and FAR means up, down, enter submenu and go back higher level menu. For setting parameter, NEAR and FAR
can increase or decrease numeral value. For Samsung cameras, OPEN and CLOSE are confirm buttons.
92#
menu operation:
