Beretta 20116162 Installation Manual Download Page 6

INSTALLATION

6

11  WATER CONNECTIONS

T

E

R

RB

SV

VE

60mm

72mm

R

 

Solar circuit return (3/4" M). Outlet of heat trans-

fer fluid towards solar collector.

RB

  Storage system return (3/4" M). Inlet of heat 

transfer fluid from solar storage system.

SV

 

Safety valve drain

VE

 

Expansion tank fitting

E

 

Solar expansion tank (not supplied)

T

 

Safety valve outlet pipe (not supplied)

-  Connect the return fitting (R) in the upper part of the 

solar station to the solar plant

-  Connect the return fitting (RB) in the lower part of the 

solar station to the accumulation system

-  Connect the safety valve drain to a pipe (T) to avoid 

burns from expelled fluid and to permit the heat trans-

fer fluid to be recovered

-  Connect expansion tank (E), suitable for solar plant 

applications, to 1/2” fitting (VE).

Fasten expansion tank as explained in the instruction 

sheet supplied with the accessory.

For hydraulic connections, use silicone seals having 

a hardness of at least 80SH. If no seals can be used, 

seal fittings with high-temperature sealant (>180°C) 

suitable for solar applications.

12  PUMP CONTROLLER

The circulator is produced with maximum hydraulic head 

configuration of 7,5 meter.

USER INTERFACE

The user interface consists of a push-button (1), a red/

green LED (2) and four yellow LEDs (3).

1

2

3

LED 1 LED 2 LED 3 LED 4 LED 5

When necessary, the user interface provides access to:

-  Functioning (performance display) mode. Pump per-

formance is displayed during functioning as a % of 

current draw with respect to rated load. Alarm condi-

tions can be seen from the colour of LED.

-  Setting Mode: Press button (1) to enter setting mode 

and select the type of pump curve.

FUNCTIONING MODE

Performance display

When the pump is running, LED no.1 is green. The four 

yellow LEDs indicate the pump's instantaneous electrical 

power consumption as shown in the table.

Nr  displayed

Meaning

% power

LED 1 flashing green

Stand-by

0

LED 1 green and LED 2 

yellow, both lit

Low load

0-25

LED 1 green and LEDs 2, 3 

yellow, all lit

Low-medium 

load

25-50

LED 1 green, LEDs 2, 3, 4 

yellow, all lit

Medium-high 

load

50-75

LED 1 green, LEDs 2, 3, 4, 

5 yellow, all lit

High load

75-100

Summary of Contents for 20116162













Reviews: