background image

Chapter 1 

Basics

 

Page 4 

 

1. Basics

 

 

 

WARNING AND CAUTION

 

 

WARNING

 

 

 

WARNING refers to possible injury to the user or significant damage to the meter if the user does 
not follow the procedures. 

 

 

CAUTION

 

 

 

CAUTION refers to restrictions and rules with regard to preventing damage. 

 

 

WARNING

 

 

Verify that all AC sources are disconnected before connecting or disconnecting the current 
transformer. Failure to do so will generate lethal voltages on the current transformer. 

 

If  you  are  not  knowledgeable  about  electrical  systems,  have  an  electrical  professional  install  this 
unit. The diagrams in these instructions pertain to the installation of the 600-ACSM and not to the 
overall wiring of the vessel. 

 

If an inverter is installed on the vessel, its power leads must be disconnected at the battery before 
the unit is installed. Many inverters have a ‘sleep mode’ in which their voltage potential may not be 
detectable with measuring equipment. 

 

If an inverter is installed on the vessel, it must be stopped and rendered inoperable before the unit 
is installed. 

 

Verify that no other DC or AC is connected to the vessels wiring before installing the unit. 

 

If the meter must be removed, connect the current transformer leads together before restoring 
power to the AC system. 

 

CAUTION

 

 

The back of the unit is not waterproof. Do not install where the back of the meter is exposed to 
water. 

Summary of Contents for 600-ACSM


























Reviews: