background image

18

Bentone  

165 105 06  

5.  Burner installation

Burner output

150 kW

Estimated nozzle output

150 kW/11,86 kWh/kg*= 12,6 kg/h

Nozzle selection in accordance with the table. (See technical data) Nozzle 

selection is based on the selected pump pressure and the desired effect. 

According to the nozzle table, this provides the following nozzle. 

Selected pump 

pressure

9,0 bar

Nozzle

3,50 gph

3.50 gph distributed to two nozzles, 

e.g. 2.0 gph at stage-1 and 1.5 gph at 

stage-2

Basic settings should only be seen as setting values to get burner to start 

and establish a flame. Once the burner has started and established a flame, 

it will be necessary to adjust the settings so that they are adapted to the 

installation in question and the fuel used at the time.

Basic settings

The setting value for 150 kW according to default settings tables. Refer to 

6.2 for the correct settings procedure. Nozzle assembly adjustment, brake 

plate B30. Air setting 6.3.

5.1  Examples of basic setting B 30

Nozzle B30-2

Burner output

150 kW

150 / 11,86 = 12,6 kg/h

According to the nozzle table, this provides the following nozzle.

Step 1

 2,00 Gph = 79kW

Step 2

 1,50 Gph = 63kW

Basic setting B30-2

The values are available in the tables for setting values of inserts or air 

dampers. 

Insert

150kW = 2

Low load air damper, orange

=40°

MV2 Open, black

=50°

Air damper step 2, red

=80°

These are the default settings and controlling the combustion will take place 

during operation.

Selection of power and connection between the different power stages must 

be selected and adjusted so that the system achieves good functionality

Summary of Contents for B 30 A2.2H









































Reviews: