The Digital Key
The Absoluta control panel supports the following digi-
tal keys.
Ø
SAT2
Proximity Key (Figure 4a)
Ø
PROXI-CARD
Card (Figure 4c)
Ø
MINIPROXI
Tag (Figure 4f)
Ø
PROXI-TAG
Tag (Figure 4g)
When you present a Key to the Reader’s sensitivity
field, you can perform the operations described in this
section.
Each Key has a random code, selected from over
4 bil-
lion
combinations, that ensure an high security grade.
Your Installer, during the programming phase, enrolls
the Keys that you can use on the system and assigns
their a label to identify the relative user: in this way you
can recognize in the Event Logger, who does what.
Also the keys are programmed to operate on specific
partitions, as per the readers.
+
In this manual, the word
key
refers to the SAT2
key, the PROXI-CARD card and the MINI-PROXI
tag and, the word
reader
refers to the ECLIPSE2
and PROXI2 readers and the proximity reader in-
side the PREMIUM Keypad, unless otherwise
stated.
The Reader’s Light Indicators
The Readers have 3 light indicators that operate de-
pending if the Key is present on the Reader or not.
n
Key at Reader
When a Key is detected by the Reader, the light indica-
tors will signal as follows.
Ø
Fast Blinking on ALL the Light Indicators
: this will
occur when a False Key is present at the Reader.
Ø
Slow Blinking on ALL the Light Indicators
: this
will occurs when not programmed keys with
PATROL option is near the sensitive field of Reader
for more than 10 seconds, or until all three LEDs start
slow Blinking, and no Arming/Disarming operation
shall be performed.
Ø
RED Light Indicator ON
: the system will Arm when
you remove the Key from the Reader.
Ø
RED Light Indicator blinking
: arming blocking con-
ditions has been detected.
Ø
AMBER Light Indicator ON
: the system will arm in
A Mode
when you remove the Key from the Reader.
Ø
AMBER Light Indicator blinking
:
A Mode
arming
blocking conditions has been detected.
Ø
GREEN Light Indicator ON
: the system will arm in
B
Mode
when you remove the Key from the Reader.
Ø
GREEN Light Indicator blinking
:
B Mode
arming
blocking conditions has been detected.
n
No Key at Reader
When no Key is present at the Reader, the Light Indica-
tors will signal as shown in the following table.
RED
AMBER
GREEN
DESCRIPTION
OFF OFF OFF
The system is
Disarmed
.
ON
OFF OFF
At least one Reader’s Partition is
Armed
.
ON ON
OFF
The system is armed in
A
mode.
ON
OFF
ON
The system is armed in
B
mode.
Fast flash on RED LED indicates a running alarm
Slow flash on RED LED indicates an alarm memory
The Partitions that are not controlled by the Reader will
not affect the Light Indicators.
+
The Installer can program the Reader’s Light Indi-
cators to signal the System status at all times, or al-
ternatively, only in response to a Valid Key (Light
Indicators OFF when no Key is present, comply
with EN50131).
Ï
Readers connected to the Absoluta 630 control
panel always show the status of the security sys-
tem.
Multiple Systems
The Keys can be programmed (by the Installer) to oper-
ate on more than one System, and to manage different
Partitions on each System.
Key operations
The Keys can:
Ø
No Action
Ø
Disarm
Ø
Away Arm
Ø
Arm — A Mode
Ø
Arm — B Mode
Ø
Patrol Disarm
Ø
Automation and Access Control
n
No Action
This operation keeps the Partitions’ status as the one
that was theirs before the Key was brought close to the
Reader.
1.
Hold the Key near the sensitive field of the Reader.
2.
Remove the Key when ALL the light indicators are
blinking slowly (about 10 seconds): in
EN50131
mode, the Reader will show the Areas’ status mo-
mentarily.
58
Expandable Hybrid Control Panels
