background image

 

FCC COMPLIANCE STATEMENT 

 

This equipment has been tested and found to comply with the limits of a 

Class B computing devices, pursuant to Part 15 of the FCC rules.   These 

limits are designed to provide reasonable protection against harmful 

interference in a residential installation.   This equipment generates, uses 

and can radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio 

communications. 

 

If you suspect this product is causing interference, turn your computer on 

and off while your radio or TV is showing interference.  If the 

interference disappears then when you turn the computer off and 

reappears then you turn the computer on, something in the computer is 

causing interference. 

You can try to correct the interference by one or more of the following 

measures: 
 

1.  Reorient/Relocate the receiving antenna. 

2.  Increase the separation between the equipment and receiver. 

3.  Connect the equipment into an outlet on a circuit difference from that 

to which the receiver is connected. 

4.  Ensure that all expansion slots (on the back or side of the computer) 

are covered.   Also ensure that all metal retaining brackets are tightly 

attached to the computer. 

 

Summary of Contents for AEN100













Reviews: