13
BRAINY CONTROL UNIT
INPUT/OUTPUT FUNCTIONS
N° Terminals
Function
Description
1-2-3
Power supply
Input 230Vac 50Hz (1-GND/2-Phase/3-Neutral)
4-5-6
Motor 1
Connection of motor 1: (4-start/5-Com/6-start)
7-8-9
Motor 2
Connection of motor 2: (7-start/8-Com/9-start)
10-11
Blinking light
Connection of blinking light 230Vac 40W max.
12-13
TLS
N.O. clean contact for courtesy light, timer, etc.
The activation time is regulated by the parameter TLS
14-15
24 Vac
Accessories power supply output 24Vac/1A max.
16-17
Lock 12Vdc
Accessories power supply output 12Vac/10W for electric lock (16:0V, 17:+12V)
18-19
AUX1
Normally Open clean contact, configurable as SCA- open gate light (default) or photocell test.
20-21
EDGE
Input, sensitive edge contact
Resistive edge: “DAS” Jumper closed
Mechanical edge: “DAS” Jumper open
When the edge is activated, the gate movement is stopped and reversed for about 3s.
22
SWO-M1
OPEN limit switch input motor 1 (N.C contact.)
23
SWC-M1
CLOSE limit switch input motor 1 (N.C. contact)
24
SWO-M2
OPEN limit switch input motor 2 (N.C. contact)
25
SWC-M2
CLOSE limit switch input motor 2 (N.C. contact)
26-27
COM
Common for limit switch and all the control inputs.
28
Step-by-Step
Step-by-Step button input (N.O. contact)
29
PED
Pedestrian button input (N.O. contact)
30
OPEN
OPEN button input (N.O. contact), configurable as Clock contact
31
CLOSE
CLOSE button input (N.O. contact)
32
PHOT
Active photocell input on opening and closing
33
PHOT CLOSE
Active photocell input only on closing
34
STOP
STOP button input (N.C. contact)
35-36
Antenna
Antenna connection for plug-in radio receiver board (35-screen/36-signal).
37-38
AUX2
Voltage-free Normally Open Contact. Configurable as second radio channel (default) or SCA-
open gate LED.
J3
Radio
Plug-in connector for radio receiver.
NOTES
The EDGE must be connected exclusively to the special inputs 20/21.
Two types of EDGE may be used:
If an edge with resistance 8K2 is used, close the Jumper “DAS”.
If a mechanical edge with N.C. contact is used, open the Jumper “DAS”.
If the edge is not used, bridge the terminals 20-21 and open the Jumper “DAS”.
TO CHECK CONNECTIONS:
1) Cut-off power supply.
2) Manually release the wings, move them to approx. half-stroke and lock them again.
3) Reset power supply.
4) Send a step-by-step control signal by pressing the button or the remote control key.
5) The wings should start an opening movement.
If this is not the case, invert the movement wires of the motor. (4<>6 for motor M1, and 7<>9 for motor M2) and the relevant limit
switch inputs (22<>23 for motor M1, and 24<>25 for motor M2).
PROGRAMMING
The programming of the various functions of the control unit is carried out using the LCD display on the control unit and setting the
desired values in the programming menus described below.
The parameters menu allows you to assign a numerical value to a function, in the same way as a regulating trimmer.
The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch.
Other special functions follow the parameters and logic menus and may vary depending on the type of control unit or the software
release.
TO ACCESS PROGRAMMING
1 – Press the button <PG>, the display goes to the first menu, Parameters “PAR”.
2 – With the <+> or <-> button, select the menu you want.
3- Press the button <PG>, the display shows the first function available on the menu.