Benewake SEN-16977 Product Manual Download Page 23

Page: 23 / 24

SJ-PM-TFmini-S A01 Product Manual

Benewake (Beijing) Co. Ltd.

Page23

Attachment 1: Introduction of TF Series PC software

This PC software only supports the Windows operating system. It is suitable for any products of TF series,
but the output of those products is limited to the serial port communication protocol. Detailed operations

are as below.

Figure 7: Interface of TF Series software

Product Type/Serial Port Control Zone [SETTINGS]

Product Type: connect the LiDAR via TTL-USB board to the PC. As shown in the figure, select ‘TFmini-

S’.

Serial port (COM): select the right serial port number corresponding to the LiDAR. Baud rate is set to

115200 as default.

CONNECT/DISCONNECT: Click [CONNECT] button to establish the connection with LiDAR. Click

[DISCONNECT] button to terminate the connection.

Function Zone [FUNCTION]

Pix Mode: check the checkbox to enable Pix mode. Uncheck the checkbox will set TFmini-S to default

output format.

In Pix mode, the frame rate (Effective Points) calculated by test software is unreliable.

FREEZE/CLEAR: After clicking [FREEZE], time-line chart in zone [4] will stop updating. On clicking

Summary of Contents for SEN-16977

























Search results

Summary of Contents for SEN-16977

Reviews:

Related manuals for SEN-16977

Brands by name

Popular brands

Benewake SEN-16977, Product Manual

Search results

Summary of Contents for SEN-16977

Reviews:

Related manuals for SEN-16977

Brands by name

Popular brands