background image

1. Features

The TBS Mini is developed for all kind of RC controlled models, f.e. air planes, helicopters, 
tanks, trucks, cars, ships, … . A large collection of original sound records is available.

New features of the TBS Mini V2:

- Onboard 3W digital audio amplifier for 4 and 8 Ohm speakers
- Volume control on board
- Easy connection of external amplifier modules
- Watch the 

limited supply voltage range of max. 6V

 (= receiver supply voltage)

Fully customer programmable. Your own sounds can be loaded!

Large sound library of original recordings available. Please check www.benedini.de

Sound quality 22KHz, 8Bit, Mono

Capability to play two sounds simultaneously (engine and one special sound)

16Mbit sound memory, enough for 93sec. at 22KHz

Internal amplifier with 3W at 4 Ohm speaker

External high power amplifiers available to meet different model requirements.

Remote 

(depending on control mode) or local volume control

Up to 6 switching outputs

- Can be triggered by a sound (f.e. Muzzle flashing) or independently (universal switching)
- Switching-, momentary- or flashing mode possible

Only 

one

 proportional channel necessary to control 

all

 functions of the unit.

Speed signal derived from the receiver. This allows combination with brushless or brushed 
motors.

Small and low weight

USB programming cable available (optional) 

Totally programmable by the free of charge software “TBS Flash”: 

- You can load your own sounds or any of the Benedini sounds available at 
www.benedini.de

Firmware update! This means you have always the latest software at you unit.

FREE OF CHARGE sound libraries available at www.benedini.de

The TBS Mini soundunit can be fully configured by the optional programming cable and a 

common PC. Please see the separate manual for the TBS Flash software.

The unit can be controlled by a spare proportional channel by one of the following modes:

12-position encoder (combination of rotary switch and push button)

3-position switch for 

direct

 sound selection

3-position switch for 

indirect

 sound selection

Autostart (

NO

 additional proportional spare channel necessary in this mode)

→ See detailed description of each mode in the according chapter of this manual.

TBS Mini V2, 11/2018                                    

www.benedini.de

                                  Page 3 of 13

Summary of Contents for TBS Mini V2














Reviews: