background image

 

RBJ Series of Rolling Bridge Jacks 

12

 

P/N 5900004 — May 2017 — Rev. A 

Moving the Rolling Bridge Jack into Position 

Rolling bridge jacks need to be moved into position using a fork lift or other device appropriate for 
lifting heavy loads. 

 WARNING

 

Pay close attention when moving the rolling bridge jack off its shipping pallet; the 
jack could move and can cause injury. Prior to removing the strapping or bolts, 

make sure the jack is held securely by a fork lift or other device for lifting heavy 

objects. 

To move a rolling bridge jack into position on the lift

1.

 

Make sure the lift is on the ground or in a locked position. 

2.

 

Using a shop crane, forklift, or other lifting device, raise the rolling bridge jack and orient it between 
the lift’s two runways. 

Do not lower it onto the lift yet

 

Remember to orient the air hydraulic pump side appropriately: if you are using just one rolling 

bridge jack, orient the pump side towards the crosstube; if using two rolling bridge jacks, orient 

both pump sides of the jack towards the outside of the lift (not towards the inside). 

3.

 

Lower the rolling bridge jack to just over the utility rails on the inside of the lift’s runways. 

Do not 

lower it onto the lift yet

 

 

Summary of Contents for RBJ Series





















































Reviews: