background image

 

RBJ Series of Rolling Bridge Jacks 

15

 

P/N 5900004 — May 2017 — Rev. A 

7.

 

Install safety brackets 

on both sides of the rolling bridge jacks

 using the provided 

hardware. 

 

This image shows the safety bracket being installed on one side of the jack; make sure to install 

the safety bracket on both sides. 
The nuts to install the safety brackets are put into place from the utility rail side; the washers and 

bolts from the jack side. 

Note

If you did not put the nuts to install the safety brackets into place earlier, you may need to 
raise the rolling bridge jack to get them into place now. 

8.

 

If you are using two rolling bridge jacks on the lift, install the safety brackets on the second jack. 

9.

 

Raise the lift (so that the rolling bridge jack is off the ground) and lock the lift at the desired locking 

position. 
If you locked the lift at a locking position in Step 1, you can ignore this step. 

 WARNING

 

Do not start using the rolling bridge jack until you are certain the lift is correctly 
situated on a safety lock. 

10.

 

Check the clearance and movement of the rolling bridge jack. Make sure the rollers are centered in 
the channel or on the lip at all points along the length of the utility rail. 

11.

 

If necessary, make adjustments to the arms of the rolling bridge jack or to the runway to ensure 

proper operation of the rolling bridge jack. 

 

 

Summary of Contents for RBJ Series





















































Reviews: