BendPak MD-6XP Installation And Operation Manual Download Page 1

Page: 1 / 44

1645 Lemonwood Dr.

Santa Paula, CA, 93060 USA

Toll Free: (800) 253-2363

Telephone: (805) 933-9970

bendpak.com

Portable Mid-Rise Scissor Lift

Installation and Operation Manual

Manual P/N 5900108 — Manual Revision F — March 2020

Models:

• MD-6XP

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠

DANGER

Read the

entire contents

of this manual

before

using this

product. Failure to follow the instructions and safety precautions in
this manual can result in serious injury or death. Make sure all other
operators also read this manual. Keep the manual near the product
for future reference.

By proceeding with setup and operation,

you agree that you fully understand the contents of this
manual and assume full responsibility for product use

Summary of Contents for MD-6XP












































Search results

Summary of Contents for MD-6XP

Reviews:

Related manuals for MD-6XP

Brands by name

Popular brands

BendPak MD-6XP, Installation And Operation Manual

Search results

Summary of Contents for MD-6XP

Reviews:

Related manuals for MD-6XP

Brands by name

Popular brands